Question Locked

Desktop connects to intenet, but can't check or send email

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

A few days ago I encountered the above problem on my desktop. The message is "connection to the server has failed" and mentions "0x800CCC0E" It seems both port 25 and 110 aren't accessible by the desktop. Fortunately, my laptop still connects to email through the wireless connection. It works fine.

I triple-checked all account information, mirrored all of the relevant laptop settings (including IE and OE and security), turned off Zone Alarm and Avast, went to "Network Connection" in the control panel and "repaired" the connection. I tried the telnet command at the c prompt, it didn't connect. No cigar. The only thing I haven't tried is resetting the TCP/IP stack. Caught a blurb that this could leave my machine high and dry because it resets all settings (or something like that."

It appears that this machine cannot connect through these ports. Any suggestions? Big Thanks in advance!!!

17 replies

by fwang

If you do, try to turn it off and test the email.

by hal 9000

Delete the E-Mail Account by opening the Mail Client then tools - Accounts and mail then delete the account and recreate it with just supplying your e-mail address/s incoming and outgoing servers and user name & password. This will most likely reset the Mail Client to a working condition.

While it's a nuisance I find that I have to do this about every 6 months on every computer for some reason best known to Windows as all of them don't fall over at once and there doesn't seem to be any reason for the failure. It just happens on different computers at different times.

Col

by grassiap

HAL answer will certainly resume the email connection. However the 0x800.... errors are related to access rights controlled via AD.
you mention port 25 and 110 (pop3 and smtp) that are not so much depending on AD.

So my question is are you trying to access an exchange mailbox (then you'll want to check around AD and your DCs, if the latter are not available, the client will use cached credentials for a while, then face "access denied") or a pop3/smtp mailbox ?

HTH
Philippe

by nick in austin

I forgot to mention in my original post that I also tried installing THunderbird and it also wouldn't connect to email.

I have two OE identities, if you are saying all I have to do is delete one of them and then replace it, that can be tried relatively painlessly (I will have to back up my folders somehow). It seems that creating a third identity with a different ID, but all the same info (logon, password, smpt/pop, etc) would be just as effective.

I'll try that tonight. If you're saying I need to delete both identities, then I guess I can try that next (more backups). If that doesn't work, should I just uninstall OE and then reinstall it?

by nick in austin

I'm pretty sure just deleting one identity and re-upping it won't work. I've had these forever without any problems. Something is blocking those ports. Could it be a security setting. What about "restacking?" the TCP/IP file.

by hal 9000

This is a painless operation in OE. Open OE select Tools then Accounts and on the next Window Mail. Here you will see your existing accounts.

All you need do is highlight one and click on Delete then highlight the next and click on Delete you'll be prompted to ask if you really want to delete this account and you just answer Yes. When both or however many are deleted all you need do is click on Add and reenter your initial details like Name & E-Mail Address than setup the incoming & outgoing Mail Servers and add your user name & password then click on Apply. Repeat this till you have all your accounts reinstated and it should work.

Personally I have 6 incoming mail accounts and on one machine I use OE to collect mail when I'm On Site and I know that this works without a problem and there is no need to do anything but delete the user accounts the way that I've listed above. With my setup all the incoming mail accounts are different but the outgoing mail servers are the same as everything go's out through the one server no matter where it arrived from.

Col

by hal 9000

DC = Domain Controller

AD = Active Directory.

Col

by nick in austin

Went to Zone Alarm Program Control, deleted "outlook express" then reopened OE. Like clockwork, ZA popped up and asked me if I should allow the connection. I said yes, always, ok. ZA let the connect through, then I got the error message from OE, connection failed.

by hal 9000

That isn't a normal Windows problem. Yes you can hose the TCP/IP stack but that would be my last resort if you can not get through on port 110 try changing the port to 9999 on all e-mail accounts and see if that works.

If you are using a Network to connect to the Internet and you are not on a domain you can open the Command Line Interface and type in [b]IPCONFIG[/b] and see what you are shown there as what working IP addresses and subnet mask you have available and then check to make sure that these are actually correct. If they are then enter this in the CLI [b]IPCONFIG /RELEASE[/b] allow that to run and then type in [b]IPCONFIG /RESTORE[/b] if that cures the problem let it run as is.

Then if you still get no joy hose the TCP/IP stack the worst that can happen is that you need to perform a clean install of everything on the machine but just in case before you trash the IP Stack make sure that you have a current Data Backup available or make one and store it in some safe place then hose away the IP Stack.

Col

by nick in austin

Okay. One Mar 30, in updated Zone Alarm to a new Version 7.0.337.000. If I turned it off, this didn't fix the problem, but if I turned off Avast, which had been working just fine, the problem corrected itself. I played with settings on both softwares without success. My solution was to go back to the previous version of ZA. Here's the question:

I like Avast. I changed to it after AVG decided to charge. My computer sped up immediately. Is there another free firewall that you guys would recommend? I don't see paying $40 to $60 for a firewall when Komando is recommending Zone Alarm. What about a better anti-virus software (free of course.)

by hal 9000

Occurring between different software and it's hell to sort out. It seems here that somehow Avast and Zone Alarm are not playing together nicely.

As you are seeing a performance increase with Advast I would tend to advise to keep it. Personally I rely on hardware firewalls in the form of Routers and Nix Boxes between the Internet and Windows Environments so I'm probably not the right person to comment on this.

I'm not actually sure what is currently available other than Zone Alarm but if the older version is working properly I would tend to think that the new version is optimised for Vista and that could be where the problems where originating from as the Windows Kernel in Vista works totally differently to the XP Kernel, so as a educated Best Guess I would tend to think that is where the problem arose.

Even the older version of AVG is still being upgraded and the new 7.5 version was only released to be available in time for Vista's release as it works better on Vista than the older version did.

Maybe someone else here who has far more experience in this area can help you out as I generally work with Business Systems where we pay for everything because there is Complying Issues involved.

Sorry That I can not offer you any better suggestions.

Col

by boxfiddler Hot topic

with a number of antivirus programs. I've been quite happy with ZoneAlarm over the years in spite of that fact.

The trick is to disable the Inbound and Outbound Mail Safe Protection in ZoneAlarm, and in some instances the AntiVirus Monitoring as well. I use Avast! and ZoneAlarm together on WinXP with no probs as long as I follow the above "rules".

This discussion is closed to new replies.