Discussion Locked

DNS Resolution

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have built a small Windows 2000 Network in my home using 1 Windows 2000 server and 2 Windows 2000 Workstations. Everything internal works fine. All components sit behind a Linksys DSL/Cable Router which is connected to the Modem. For some reason sometimes the DNS resolves but other times it doesn't. Someone said I needed to setup forward lookup and reverse lookup zones in DNS on my Windows 200 server so that the clients would be forwarded to the ISP's DNS servers. I have all the IP's I need. How do I do this ?

5 replies

by timwalsh

1. Go to Start Menu | Settings | Network and Dial-up Connections | Local Area Connection and click Properties. Highlight Internet Protocol (TCP/IP) and click Properties. If your server already has a fixed IP address, verify that the Subnet Mask is255.255.255.0 and the Default Gateway is the internal IP address of your router (probably 192.168.1.1). If it doesn't have a fixed IP address, give it one (probably at the lower end of the 192.168.1.x address range). In the Preferred DNS server window, enter your servers IP address (so that the server looks to itself first). Leave Alternate DNS server blank, and click OK. If you made any changes in TCP/IP setup, you will be told to reboot.

2. After reboot, install the DNS software (if it isn't already loaded): Control Panel | Add/Remove Programs | Add/Remove Windows Components; Scroll down to Networking Services, highlight it and click the details button; check the box next to Domain Name System (DNS) and click OK; Once back at the Windows Components window, click next and follow instructions.

3. After you reboot, open the DNS tool (Start Menu | Programs | Administrative Tools | DNS

4. If you have never attempted to set up DNS on this server before you will have access to a configuration wizard that will step you through the process of setting up both your forward and reverse lookup zones in one pass. I will step you through each zone separately as I don't have access to that wizard.
(cont.)

by timwalsh

(cont.)
5. The name of your server should already show. Under the server you will see 2 empty folders: Forward Lookup Zones and Reverse Lookup Zones.
Right-click on Forward Lookup Zones and choose New Zone. This starts a wizard similar to the one mentioned above. At the opening screen click Next. Choose Standard Primary and click Next. Give your zone a name (i.e.myzone.local). Use the .local extension as your zone will not be (and should not be) viewable from the Internet. Click Next. At the next screen accept the default file name provided and click Next. At the last screen, click Finish and your Forward lookup zone is created.

6.Right-click Reverse Lookup Zones and choose New Zone; This will being up a wizard similar to the other one; At the opening screen, click Next; Choose Standard Primary and click Next; For Network ID, enter the first three octets of you IP address (192.168.1) and click Next; At the next screen accept the default file name provided and click Next; At the last screen, click Finish and your Reverse lookup zone is created.

7. Right-click the Forward lookup zone you created (myzone.local) and choose Properties. On the General tab, change the Allow Dynamic Updates window to Yes and click Apply. On the Zone Transfers tab, uncheck the box next to Allow zone transfers and click Apply and then OK.

8. Right-click on your server and choose properties; Click on the Forwarders tab and check the box next to Enable forwarders; In the IP address Window, enter the IP address of your ISPs DNS server and click Add (if your ISP has multiple DNS servers, enter them all in this manner); Click Apply and then OK.

9. On each of your workstations, change the TCP/IP properties so that the Preferred DNS server is your DNS server.
(cont.)

by timwalsh

Your DNS is now set up so that all DNS queries relating to your local network are resolved at the local level, and only thse queries related to the Internet are forwarded to your ISP.

Hope this resolves your problems.

by degthat

Thanks, it worked and I really appreciate it. I thought I was on the right track.

This discussion is closed to new replies.