Discussion Locked

Exchange can recieve email but not send

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have one Exchange Server 5.5 and have configured the IMS and checked the SMTP prt 25 to ensure it can recieve email via telnet. The problem I am having is that every time I send email out I immediately get NDR report. I have searched the KB articles at Microsoft and performed their fixes with no solution. My regions DNS server does not allow for _ (i.e. EAT_JOES) and my server name just happens to be EAT_JOES format. I would not think that to be a problem since I can recieve email. I have configured the host name to coincide with the DNS server name. If anyone can help it would be mucho appreciated.
NDR report is as follows:
Your message did not reach some or all of the intended recipients.

Subject: This is a test
Sent: 11/16/00 7:21 AM

The following recipient(s) could not be reached:

'meto8@hotmail.com' on 11/16/00 7:22 AM
The recipient name is not recognized
The MTS-ID of the original message is: c=US;a= ;p=HRE;l=HRE_H28MCF-001116122045Z-2
MSEXCH:MSExchangeMTA:HRE_H28MCF:HRE_H28MCF

Thanks
Rick

12 replies

by tony.colgrove

This seems like it could be a DNS issue. The DNS server your Exchange Server is using might not be connecting to the internet properly. Try this:
Run NSLOOKUP from the command line.
Type the following commands:
set type=MX
hotmail.com

You should see the following result:
hotmail.com MX preference = 10, mail exchanger = mail.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc2.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc4.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc5.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc6.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc7.law5.hotmail.com

mail.hotmail.com internet address= 216.33.151.135

If it cann't properly find the domain, you would see this:
**** can't find hotmail.com: Non-existent domain

If you get the second result the DNS server is not configured correctly. You could try a differentDNS server (one from your ISP).

Hope this points you in the right direction.

by lastsurvivor

This seems like a silly question but do you have an IMS (Internet Mail Service running on your server or are you bouncing mail off of another Mail Gateway. It sounds to me like either the IMS or your other Mail Gateway cannot get to the Interent or in the case of the Mail gateway you are sending to is not accepting your outgoing messages. Sorry if this off base but it could be a possiblity since you mention nothing about your IMS configuration.

by jerrym mcse+i / a+

Hi Rick,
I have a few questions and some things to look at,
how is exchange connecting to the internet? direct, through a proxy server? firewall? router?....you need a port open for inetid to be open as well as a port for dns, how you set thisup depends on how you are connecting, also how is the IMS configured to send mail?... if sending using dns then you definately need the ports for dns and inetinfo.....
Thank you for the post!...jer

by mrochr

My Exchange Server is wide open connection....It is set up for DNS ...what inet port are you refrencing.....
Rick

by mpdcsup

I see X.500 addressing is occurring. Would you try sending the same message, but this time for the recipient try SMTP:meto8@hotmail.com?

by mpdcsup

If this works, it may take me a little while to look it up, but I can get you the proper changes.

by mrochr

Did not work....Im building new server and will then move the Exchange mailboxes to new server.

This discussion is closed to new replies.