Question Locked

HELP! I accidentally disabled my on-board graphics card...

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
While attempting to force Windows to recognize my nice graphics card I accidentally disabled my on-board graphics card. Now I'm staring at a completely black screen whenever Windows starts up. I need to re-enable my onboard graphics card, but the only tool I have is BIOS setup (which as far as I'm aware won't let me do anything).

20 replies

by w2ktechman

If you cant get in to safe mode, then pull the card and place it in a different port, or switch to the on-board video (if avail) and ininstall the disabled device.
After it has been uninstalled, or changed ports, reboot and Win should detect it again

by w2ktechman

for the monitor? Plug in the monitor to the other port. The pull the video card out that you added.
Or, if not, you should be able to change the port that the card is plugged into.

Both of these require opening your system. If you do not know what you are doing, it is best to take it to the shop. You certainly do not want to damage anything.

by jobart16

if you remove the cmos battery for like 10 secs, it will erase all saved settings in the bios.kinda like a force reset for your bios.

by oh smeg

If it was in BIOS you can re enable it by clearing the BIOS.

If it was in Windows you need to boot with something different that allows you access to the Windows Partition so you can make a change to the settings or do a Repair Install of the OS.

You can try a Live Linux to boot from and access the Data on the HDD or in a worst case scenario you can follow the makers instructions and do a Repair Install. Though you need to list the OS you are using and anything that you have enabled in that OS so that you do not destroy your ability to access your own data.

For Instance if you are using XP Pro running Windows Encrypted File System and do a Repair Install you will overwrite the Encryption Key and be unable to access any Data on the HDD again unless you have a copy of the Encryption Key that you can mount.

Col

by pyromike3000

I disabled the video card by doing the following:

- Right-click on Desktop
- Left-click Properties
- Goto Settings Tab
- Left-click Advanced Button
- Goto Adapter Tab
- Left-click Properties Button
- Under General Tab: Device usage: Do not use this device (disable)

If anyone knows how to reverse this mistake, please let me know!

by jobart16

boot in safe mode then try to enable it again.

by pyromike3000

I have another port for the monitor, but I've already tried switching the plug over and removing the new video card, to no avail.

Does anyone know how I could restart my system in MS DOS mode and then use some sort of command like ENABLE (where servicename is my graphic card/driver)?

by w2ktechman

you should be able to switch primary video adapters manually.

Or, you can boot into the recovery console and enable the video card from there.

by mrschofieldesq

i had the exact same problem: i disabled both my old video card and then the onboard video in device manager and would get nothing but black screen after windows started. the same thing happened in safe mode and recovery console, since it was still windows and the setting not to use those drivers.

i downloaded ERD Commander here:
http://www.keshzone.com/2007/10/winternals-erd-commander-2005-ready-for.html

then burned the iso with alcohol 120 to make a boot disk. this program boots to an OS very similar to Windows, but it detects its own devices, so you monitor will work. from here, you can access various windows settings, including drivers. so you can enable your vga driver. also, if you have windows doing automatic recovery points, you can just restore from a recovery point before the problem.

I recommend always keeping an ERD Commander boot disk around. works wonderfully.

by tsvpipers

I've done everything you suggested and my blank-screend PC doesn't seem to recognise the ERD disk when rebooting. Any ideas?

by oh smeg

You need to change it from Floppy, HDD, Optical Drive to Floppy, Optical Drive, HDD.

Just do not use any device that you do not have so if you don't have a Floppy the Boot Order needs to be Optical Drive, HDD.

You should see the POST Message and be able to enter BIOS to change the Boot Order.

Col

by seanferd

you can get almost any bootable ISO to run off a Flash drive.

Having a (legal) copy of ERD Commander is on you.

But why not boot in Safe Mode and re-enable the driver? If you can't for some reason, use Recovery Console and load the driver.

by dmiles

1)Can you just reverse the process you performed to disable the graphics

2)If you have the motherboard manual,check for reference to key that opens bios setup (ex. Del key),once open go to advance menu scroll through and locate the graphics line,highlight and then right click and choose eanble

If you have a graphics card installed in slot on motherboard,uninstall,this would cause a conflict and render no graphics

by tsvpipers

Ok, i got it to recognise the disk burnt with the iso file. but now it says the disk is not boot media. any more ideas?

by oh smeg

If not you have only burnt the Downloaded file and not converted it into the Bootable Format that you need.

Look at your Burning Software to see how to convert the ISO Image to a Usable Format.

Col

by deotriese

I was just guilty of this problem, having attempted to force my computer to use the Nvidia graphics card instead of the Intel one, which keeps causing a game to crash on a brand new laptop.

What you want to do is find your Device Manager in System Settings, Go to Display Adapters, right click on the card you disabled then re-enable it. This option isn't available in Personalisation>Display>Advanced Settings, etc. until you do this. Don't know if it's a fix for everyone, but it worked for me.

Hope I helped!

This discussion is closed to new replies.