Discussion Locked

Help me before they ruin another printer

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Is there a source to go to to find the correct transparency media for a specific printer? I am having a very hard time getting specifics from the manufactures on what to use.

I work as tech support for a high school and we have teachers who want to print transparencies. We have a variety of printers, desktop Dell laser printers and some workgroup Dell Color Lasers.

Luckily the Canon photocopier they tried to use was still under warranty so we didn't have to pay when it needed to be rebuilt. The wrong transparency media fused it together. We now know the specific brand to use for this device. But I want specifics for all of the other printers.

So far all I can find from Dell is to make sure that transparencies are laser (color/laser) rated and to verify that the printer (on the printer's control panel) is set to transparencies.

Any suggestions?

12 replies

by mjd420nova

Every users manual I've ever read had some kind of spec as to whether transparencies could be used and what the requirements were, thickness, material ETC. Yes, feeding too thin a transparency into a laser printer will certainly create a real mess and earn many dirty looks and distain from support people. The best transparencies are made on a plotter using felt pens.

by deepsand

The "Discussion" forum is for matters of general discussion, not specific problems in search of a solution.

Post problems such as this to the "Question" forum, rather than the "Discussion" forum. There are those who specifically seek out problems in need of a solution, and that's where they go to look for such.

by mc_user

My intent on this forum was to see if other techs have had similar problems with people ruining equipment via bad print media. I was hoping, by sharing of experiences, to find out if there was some motivational approach or training that was effective in educating the user to this potential problem.

Also, if I could get some opinions on some low quality product to avoid, so much the better. Thank you.

by mc_user

There is one sentence in the user manual that states "see user guide" for transparency specifics. I don't have a copy of the "user guide" and is not available on-line.

by nicknielsen

Just make sure the media are rated for copier or laser printer so they don't, well, fuse the fuser.

by w2ktechman

The media ratings are usually laser & color laser, or inkjet & bubblejet.
There may be specifics on some models, like thickness requirements, but the majority of newer printers should be able to take them well.
If you cannot find user manuals for your printer by manufacturer, it may be an old printer. I can look up and see if it is an HP printer, since I have access to an HP DB for older printers. Please PM me if this is the case and I will get it to you as soon as I can.

by mc_user

Specifically the Dell 3000cn color laser and the Dell 5100cn color laser. Both use multiple toners, cyan, magenta, yellow and black to do a multi-pass print.

The printers are out of warranty (no support) and I have not had any luck trying to locate the recommended transparency specifics on the Dell web site.

by dr dij

usually say which type of printer it is for.. inkjet or laser

you could get a cheap straight thru laser like brother cheapie models for things like that.

by mc_user

I have copies of both of those manuals. Neither manual specifies the type of transparency to be used in the printer. There is a one sentence footnote in the manuals to see the "User's Guide" which I can't find.

by mc_user

The information I needed was buried a couple sub folders down on the driver installation CD.

They state:

Selecting Transparencies:

The printer can print directly on transparencies designed for use in laser printers. Print quality and durability depend on the transparency used. Before buying large quantities of any print media, Dell recommends trying a sample first.

The Paper Type setting should be set to Transparency to help prevent jams. (See "Paper Type" for detailed information about this setting.) Check with the manufacturer or vendor to determine whether your transparencies are compatible with laser printers that reach temperatures as high as 205?C (401?F). Only use transparencies that are able to withstand these temperatures without melting, discoloring, offsetting, or releasing hazardous emissions.

by deepsand

1) The "Questions" forum provides for your feedback, by way of your being able to mark "helpful" responses as such. This does not necessarily mean that a given response contained the complete solution to your problem, but only that it served to guide you toward it. This is intended to serve as an aid to those who may in the future have a problem similar to yours, so that they might have a ready source of reference available, thereby perhaps obviating the need for them to repeat questions previously asked and answered.

2) The revised TR makes it quite difficult to find both "Discussions" and "Questions" that have not had a fairly recent post, owing to some functions comingling them in the listings. By keeping each type in their respective forums, it is easier for all to find what they are seeking.

This discussion is closed to new replies.