Question Locked

Help with manually configuring a static IPv6 network

0 helpful
1 reply
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,

I have a private OpenStack environment which works fine apart from IPv6. I'm trying to setup an IPv6 network whereby 3 VMs can talk to each other over IPv6. The DHCP element is not working but I should apparently be able to statically configure. However I have no idea how to achieve this. Is this something someone can help with?

andy@ap-ipv6-demo-01:~$ ip a
...
2: ens3: mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether fa:16:3e:7d:41:6b brd ff:ff:ff:ff:ff:ff
inet 192.168.17.80/22 brd 192.168.19.255 scope global dynamic ens3
valid_lft 86318sec preferred_lft 86318sec
inet6 fe80::f816:3eff:fe7d:416b/64 scope link
valid_lft forever preferred_lft forever
3: ens4: mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether fa:16:3e:de:cb:29 brd ff:ff:ff:ff:ff:ff
inet 10.0.10.2/24 brd 10.0.10.255 scope global dynamic ens4
valid_lft 86318sec preferred_lft 86318sec
inet6 fe80::f816:3eff:fede:cb29/64 scope link
valid_lft forever preferred_lft forever

andy@ap-ipv6-demo-04:~$ ip a
...
2: ens3: mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether fa:16:3e:c9:e2:88 brd ff:ff:ff:ff:ff:ff
inet 192.168.17.144/22 brd 192.168.19.255 scope global dynamic ens3
valid_lft 84167sec preferred_lft 84167sec
inet6 fe80::f816:3eff:fec9:e288/64 scope link
valid_lft forever preferred_lft forever
3: ens4: mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether fa:16:3e:6f:fb:57 brd ff:ff:ff:ff:ff:ff
inet 10.0.10.13/24 brd 10.0.10.255 scope global dynamic ens4
valid_lft 84167sec preferred_lft 84167sec
inet6 fe80::f816:3eff:fe6f:fb57/64 scope link
valid_lft forever

andy@ap-ipv6-demo-02:~$ ip a
...
2: ens3: mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether fa:16:3e:f6:31:c2 brd ff:ff:ff:ff:ff:ff
inet 192.168.17.56/22 brd 192.168.19.255 scope global dynamic ens3
valid_lft 86306sec preferred_lft 86306sec
inet6 fe80::f816:3eff:fef6:31c2/64 scope link
valid_lft forever preferred_lft forever
3: ens4: mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether fa:16:3e:fd:eb:c1 brd ff:ff:ff:ff:ff:ff
inet 10.0.10.24/24 brd 10.0.10.255 sco

Any help gratefully received!

1 reply

by techguy98

In Settings go to Network & Internet and click the Properties button for the interface you wish to configure. Click the Edit button under IP settings, change the configuration type to Manual, enable IPv6, and populate your settings

This discussion is closed to new replies.