Discussion Locked

Higher modem connection speed

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Is there any way to increase the speed of the connection at which a dialup modem connects to the ISP? I know the maximum connection speed setting but it doesn't have any effect over the connection speed.

21 replies

by dmiles

Open the Control Panel and double-click the System icon,on the Device Manager tab,cleck the plus beside Modem and highlight select properties,select Connection Tab,then click the Advanced button in the Extra Settings box add ATS11=50
You can also try try third party software such as MTU to boost connection settings.

by ebob

There's a lot going on, especially with a dial-up modem connection, that the likely is answer is: "no".

However, as SoulRider suggests, you can try to go into your modem and play with the various S-registers. The specifics depend on your modem, so I suggest grabbing a manual from the box, or the mfgr's website.

It's very important to understand that to get the maximum performance from a dial-up modem connection requires co-ordination between BOTH modems. Issues like error checking, compression, etc. absolutely must be synched, or the 2 modems will agree to fall back to some default, which usually results in lower than optimal speed.

Another thing you need to consider, but over which you have essentially no control, is the quality (and length) of the phone lines between you and your PTT's CO (same for the ISP and their CO). There's only so much you can squeeze down the line.

Hmmmmm, that all sounds pretty negative. Oh well.

by csmith

The actual speed of the connection is determined by the two MODEMs (Yours and the ISP's) during the "handshake routine" (The beeps and squawks at the beginning.).
The speed limit is determined by the "Line Quality" that they sense.
If you are getting slow connections (28.8k or worse on a 56k MODEM) , contact the phone company for a service call, after you have verified the problem is not in the interior phone wire, or in the MODEM.
If you are getting 40k+ connections, get a Cable MODEM connection (Roadrunner).
The speed of Roadrunner is unmachable by any other consumer level connection, and is not much more expensive than dial-up.
Regards, Chris

by sfhsgrad00

Your current connection speed is determined by, as someone mentioned before, your "handshake" between your modem, and the ISP's modem. Unfortunately, you cannot really speed that up. The biggest reason, is that Federal Law prohibits connection speeds above 56Kbps. So, even though you may have a 56K modem, you won't even connect at 56K. You can try using internet accelerators, but they will not increase your connection speed. Software like NetSonic and MarketScore, only load content from sites you have visited, at an accelerated rate. The only other alternative to increasing speed, would be to use a different form of connection, (i.e. DSL, or RoadRunner). I apologize if this isn't what you wanted to hear, but there really isn't anything you can do.

by crowstouch

Here is what I have done to improve my dial-up modem connection:

Go to Run: MSCONFIG - Click on tab for WIN.INI - Go to Ports. For the COM your modem connects through there will be a listing of; COM2:=9600,n,8,1,x (it may read COM3, COM4, etc.). Change the 9600 to read: 921600. Click apply, OK, then restart your computer. Go to the Modem Properties, change the baud rate to the highest listing it shows.

You can add what soulrider mentions in the Advanced area of the Modem properties if want. Add S10=255 as well, seperated by a comma (I think that would be okay, if have trouble with both numbers applied, keep one or the other). The S10=255 keeps the connection from being disconnected if hits a certain time factor or limitations at theServer.

When connected to Server check the bps. This will change each time you connect. IMPORTANT: The connection speed will be whatever the Server is putting out to you, minus the interferance, and drop-off from modem to modem connection. You should be running at a faster speed. Check speed at DSLReports.com.

Look into DSL or Cable, they give the best speed for the cost.

Good luck.

by raamis

The Problem:
My modem - 3Com U.S. Robotics 56K Voice Internal PCI - which I've bought recently, takes a lot of time in connecting, it connects on a low speed and frequently disconnects. It has never connected on a speed greater than 31.2 KBPS. There is nothing wrong with the phone lines or the ISP because when I connect from another computer in my house using the same phone line and ISP, it connects in a flash and at a very good speed and never disconnects. The modem in the second computer is Zoltrix Conexant 56K internal (a lot cheaper than USR). Both computers are brand new and have Windows XP installed and there is nothing wrong with other hardware or software as they run perfectly well otherwise.

by raamis

Country problem?
Could it be that the modem is not compatible with the phone lines here in Pakistan or with the ISP's modem? The Zoltrix one is very popular here and almost everyone has it whereas I haven't heard of anyone using the USR here. Its not even available in the market and I had to ask a friend in Dubai (UAE) to bring it for me.

I have also contacted the support personnel in USR but they haven't come up with a satisfactory response uptill now. They say the drivers need updation while there aren't any updates available on their website.

by csmith

Assuming, from your comments, that you have unplugged the cable from the USR and plugged it into the Zoltrix, and the problem disappeared, this is a hardware problem.
The USR MODEM is defective.
I have seen this with all brands of MODEMs.
Get a return authorization, and exchange for another MODEM, or however returns are handled in Pakistan.
I hope all goes well, this sounds like a difficult situation for getting service/support.
Regards, Chris

by csmith

:
By the Way.
The COM setting in the above answer, for WIN.INI , is incorrect.
The setting should be
115200,n,8,1,p
The p forces hardware flow control.
Definitely necessary for program downloads to be glitch free.
Regards, Chris

by mgriego

I worked at 3com and supported these modems and I can give you some insite. First, however the FCC regulations quoted earlier are only required for U.S. Territories. The phone signal strengths in international countries are much higher. So reaching56k or above can be acheived.

Now for the 3com modem. In the earlier 56k models before v.90 or x2 became the standard 3com had developed and sold these modems as 56k modems but did they didn't really do 56k. When v.90 became the standard these earlier modems could do 56k with a firmware upgrade flashed to the modem. It could be possible you may have one of these earlier modems. Just upgrading window's modem drivers will not solve the problem. So try to get the firmware upgrade for yourmodem and see if that works. If not then it could be a defective modem.

by yasirs

Hi,

Luckily I am from pakistan too , well no matter what u do can not physically go above the 19.2Kbps connectivity treshold in pakistan , it was physically proven via this article I read. Also as per the speed get the best modem US robotics is good and have it to be 56k minimum. Also to dream of anything above that in pakistan is about 5 years away ?500 for a 64Kbps leased line GET REAL PTCL.

I hope thats a help , Byez.

This discussion is closed to new replies.