Discussion Locked

HotSynch Nightmare!

0 helpful
27 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I received a new Palm 505 for my birthday and can not hotsych at all...I tried with work pc, home pc and even laptop...but no luck. I am trying to connect with USB cradle. Please help! Thanks.

27 replies

by alpha-male

Can you give us some more specifics? What OS are you using? What error are you getting? How is your hotsync configured? The more specifics you give, the more likely we can help....

That said, I've had a few snags with the USB palms syncing as well. I resolved them by setting up custom connections and tinkered with the settings...eventually coming up with one that worked. With the Serial connectors, I've found tweaking the speed settings sometimes helps as well.

by datacon

OS trying to hotsych to is either Win98(2ndED) or Win2000Pro. The error is "cannot establish connection with desktop, check settings and try again."

by qballrail

I use a Sony Clie, shyed from the Palms for this reason. However, I did run across one similar issue to yours and simply reinstalled the Sync software and everything worked fine. Sometimes, however, you may need to do a full removal of the Palm software and a clean install. Make sure you have all the necessary components installed. Is the Hot-sync Manager loaded on startup?

by pj

Do you receive a message when you plug the USB Cradle and press the button??

Pablo.-

by lkrolak

I hate to ask an obvious question, but are you sure your USB port is working.

I ran into a situation where it was not functioning and thus causing the problem. There was a conflict in the OS.

by maxwell edison

The software for your device must be installed with the device UNPLUGGED from your computer. I suspect this may be your problem.

by michael j

Saddly, we're left with this....
Synch Software (OK) - USB Port on Comp (OK) -
Cradle (Replaced x2) - Palm.....

The only other possibility would be the data connection strips on the Palm itself - they likely aren't getting signal through to the cradle.

I don't know how to test for this at this time, but PALM TECH should be able to tell you if a simply diag is possible - like testing the strips with a Volt/Ohm meter.

by tjc

make sure that you are using the same OS on the palm as is the desktop software you are hotsynching to. Also if you can take it to a freshly installed windows computer that has nothing else installed on it and then install the desktop software and the hotsynch device and try.

by tim

I had 10 Palm m505's that had sync trouble and it was
driving me crazy. It turns out that there is something with
the m505 and static (you have no idea how long we were
looking for a cause). If you got a staic shock and were
holding your palm or trying to put it in the cradle then it
will work but it will never sync again (or at all). You can call
palm, they know about this and will send you a replacement
unit. One palm tech told me to change the cradles and I did
on one unit and it didn't solve the problem. Good Luck.

PS- They are going to ask you to give them your credit card
number, they won't charge you if you send back the bad
unit.

by millerst

Check your hotsync COM settings. Make sure when you install the software you select USB connection and make sure the settings for you COM port on the hotsync software are correct. Try changing the com port if you still have problems.
Also make sure that your pc is seeing the com port the hotsync is tring to communicate to. Sometimes the Hotsync program will look for a com port that doesn't (yet) exist.

by kcrandall

I've had a similar issue and it has always been a conflict on the serial interface. Even when using the Infrared port HotSync requires that COM1/COM3 be available. If I happen to be dialed in on a modem, Hotsync won't work. I have to shut the modem down and then Hotsync. does your device have an infrared port? if so try that instead of the cradle. Make sure to change the connection type on both the Palm and the Desktop.

This discussion is closed to new replies.