Discussion Locked

how do i speed up printing in NT/98 envi

0 helpful
23 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
i've just been assigned to a rather small NT4.0 SP5 network (12 users) running DHCP. when the users print to an HP5 printer that is setup through a HP jetdirect 500X and shared from the server, it can take up to 20 minutes for the one page job to print! i can see it sitting in the queue but it just won't start printing!! how can i make the server begin the process quicker? like as soon as it arives in the queue? spooling is setup.

23 replies

by kellyst

I would use LPR printing instead of HP port. The printers will need static IP addresses, but it is very quick.

by jim.cook

You don't say if the server is printing to the JetDirect card using LPD(TCP/IP) or DLC. Also, have you been receiving any type of notifications in your event log on the server regarding printing?

My first guess would be that you are using LPD toprint to your JetDirect cards and that you are experiencing time-outs when your server attempts to connect to the JetDirect card (the event logs should confirm this.) One recommendation I would make is to use DLC to print to the JetDirect cards andconfigure the DLC port to establish a continuous connection the printer.

However, more information might lead me down a different path.

by Member 35772270

I use to think that HP Jetdirect was better then candy, until I had your problem. I eliminated my problem by uninstalling Jetdirect and using TCP/IP printing.

Setup a test printer and try it, Install a LPR port on server then assigned it an IP address, give it a name and then shared it and set the access permissions.

Since you are running DHCP, don't forget to exclude the IP, so that it will not try to assign it something else.

You will have to install a new monitor to get the LPR port, and you will be given an opportunity to install drivers for other OS's (95/Nt etc.) during the share phase.

by ccsbz

I have the same setup you have.(14 users)with three other printers and i don't have this problem. i have spooling setup to start printing immediately. avg 15 ppm.
hope this helps.
DJ

by andrewshen

1. Take a look into your clients printer driver, the PCL and PostScript driver make a difference, also the setting of resolution.

2. Adjust the setting in Scheduling tab at printer Properties.

3. .... your network is too busy?

If you have only one printer, spooling is not needed.

Hope this help :)

by gniazdo

I have to agree with Dennis@l 's answer. I experianced the exact same problem about a year ago. The best thing you can do is assign a static IP address to the printer and remove the address from your scope in the DHCP administrator. Then choose LPRfor the printers port and share it. I don't know why but the whole HP jet direct port has always given me problems ever since I have always used tcp/ip printing services with no problems.

by phigginson

Hi,

I think you need to read this article in KB Microsoft

ARTICLE-ID: Q179156
TITLE : Updated TCP/IP Printing Options for Windows NT 4.0 SP3 and Later

Good Luck and Happy New Year

Pascal h.

by bound4doom

I have to agree with everyone that said go with the TCP/IP standard printing. Just assign a static IP address to the jet direct cards for the printer then just do a standard TCP/IP printer set up and away you go. Lots of benefits doing it that way too. Basically every operating system with TCP/IP can print to that printer. You can use the plain windows telnet program to connect to it and make changes in config right from your desk. Realy if you are running in an NT environment with the TCP/IP protocal running it is by far the best way to print

by redwings

If you are running SP3, upgrade to SP5 for starters.
Here is the fix for your slow NT printing and I guarantee you will see significant printing.
1) Start the Registry Editor(Regedt32.exe) and go to the following key:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\LPDSVC\lpr
2) On the Registry menu, click Save Key and type a filename to save it.
3) Delete the Lpr key to remove all of the individual IP Address entries.
4) Select the LPDSVC key.
5) On the Edit menu, click Add Key, and the type "lpr"(without the quotations) in the Key Name box.
6) Select the newly created Lpr key.
7) On the Edit menu, click Add Value, and the type the following information:

Value Name: UseNonRFCSourcePorts
Data Type: REG_WORD
Value: 0 or 1
0 = uses ports 721-731 (default)
1 = uses any port > 1024

My recommendation is to use the 1 and basically opens up unlimited ports beyond 1024, and your printing will go through the roof.
Don't forget to stop and restart the Spooler service by going to the DOS Prompt and typing,

by redwings

This applys only to the NT Server 4.0. I have not tried it on the NT 3.51 Server.
If you are running SP3, upgrade to SP5 for starters on your NT Server 4.0.
Here is the fix for your slow NT printing and I guarantee you will see significant printing.
1) Start the Registry Editor(Regedt32.exe) and go to the following key:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\LPDSVC\lpr
2) On the Registry menu, click Save Key and type a filename to save it.
3) Delete the Lpr key to remove all of the individual IP Address entries.
4) Select the LPDSVC key.
5) On the Edit menu, click Add Key, and the type "lpr"(without the quotations) in the Key Name box.
6) Select the newly created Lpr key.
7) On the Edit menu, click Add Value, and the type the following information:

Value Name: UseNonRFCSourcePorts
Data Type: REG_WORD
Value: 0 or 1
0 = uses ports 721-731 (default)
1 = uses any port > 1024

My recommendation is to use the 1 and basically opens up unlimited ports beyond 1024, and your printing will go throu

This discussion is closed to new replies.