24 replies
by chipmunk
Sorry I'm not clear on your question, but I can tell you where the workgroup name is located, Go to Control Panel - click on Network Icon, then click on Identification tab, and you'll see the Workgroup name.
Why do you want to go into hte Registry?
Workgroups floating around for weks ???
Alvin
by scalver
by chipmunk
This is Alvin again... I'm just beginning to think ...Do you mean Mapped Drives poppinhg up after loggin into Windows ??
If that is the case.. Then goto MY Computer Icon you'll see your C drive Icon ...the mapped drives look like the same icon except you'll see a pipe under the drive... just right click on it then select disconnect ...
by scalver
by etowah
Do you ever re-boot these machines?
When you reboot the non-existant workgroups should disappear.
by scalver
by rmmcp
If your referring to mapped drives, open Windows Explorer, right click the network drive and select Disconnect.
If you are talking about bogus workgroup names or computer names in Network Neighborhood, you'll have to review how the workstation computers' Identification is setup in Network Properties. Make them right and reboot the workstations.
If this happenned via a bad logon batch file, remove any referrence to the batch file from the Autoexec file. Run Sysedit and preceed the entry lines with REM. Then reboot the machines.
I'm not quite following what you're talking about.
by scalver
by svanscoter
Your problem is related to what is called Master browser. On every network, there has to be a boss that controls the list of what resources are on the network. Now, I haven't worked with Peer-to-Peer networks in a while, but here is a link that willgive you some insight into it. It talks mainly about NT, but has some useful info that could steer you in the right direction. Hope it helps.
http://www.microsoft.com/TechNet/winnt/Winntas/Tips/platinum/ptbimsn.asp
by scalver
by svanscoter
Here is another link, if you can sift through the tech stuff, it talks about the master browser. Also, I believe that the command nbtstat from a command prompt will clear the list, but don't quote me on that. type nbtstat /? at a command prompt for the switches. I think you will have to use the -R switch.
http://www.microsoft.com/TechNet/win95/technote/w95brows.asp
by scalver
by stevenreedsr
by scalver
by uriyt
Normaly none-existing resource must dissapear
45 min. after correct windows logoff.
In such a big peer-to-peer network you'l better try to assign static master browser by disabling "master browser" in File and Printer sharing for MS network on all WS except one (on which it must be set to ENABLED). It must be fastest and fewer used WS. On one or two WS you must set this switch to AUTOMATIC (for backup purposes)
by scalver
by tysonmathews
Your network neighborhood is active and therefore id old workgroups are showing up, that means somewhere someone has the old workgroup list somewhere. Maybe all the changes in workgroup name have been changed but that doesn't mean it isn't listed somewhere else. depending on the size of the network try this in your ms dos prompt with each IP
nbtstat -a ip
it will give you an exellent resource and show you exactly what is on each machine.
foe example here is mine
--------------------------------------------
C:\DOCUME~1\ADMINI~1>nbtstat -a 10.0.0.3
Local Area Connection:
Node IpAddress: [10.0.0.3] Scope Id: []
NetBIOS Remote Machine Name Table
Name Type Status
--------------------------------------------
ROBINHOOD <20> UNIQUE Registered
ROBINHOOD <00> UNIQUE Registered
WORKGROUP <00> GROUP Registered
WORKGROUP <1E> GROUP Registered
ROBINHOOD <03> UNIQUE Registere
by scalver
by dennis2841
by scalver
by ryank
Make sure you have absolutely every last PC on your network configured with the correct workgroup name. Then shutdown all of your PCs to make there is no Browse Master with no old data on it.
It sounds like you may have a workstation with an incorrect workgroup name and that doesn't have file and print sharing on. This would cause the workgroup to still appear and there to be no computers in it as the PC doesn't announce itself to the LAN if there are no resources on it.
by scalver
This discussion is closed to new replies.
Trending Windows Forum posts
Sort by Trending