Question Locked

HP 3030 prints garbage

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I am having a problem with my HP 3030 printer. It normally prints fine, but occasionally it will try to print one document (such as an e-mail) and will have a problem and start printing page after page of a blank sheet of paper, except for one line of garbage at the top. The line ususlly consists of sympols (hearts, diamonds, percent marks, etc.) I have reinstalled the software and tried updating the driver but it still messes up from time to time. Anyone else having this problem and how do you fix?

9 replies

by captbilly1eye

What Operating System?
Does the situation happen following a reboot with the first print job or does it happen on consecutive print jobs following good ones with no reboot in-between?

The issue you described usually happens when a printer is left on all the time.

The simplest workaround for this issue is to turn the printer off before turning on the computer or restarting Windows. Once Windows has finished loading (when the icons appear on the Windows desktop), turn on the printer. If power cycling the unit does not correct the issue, try using a different or new parallel cable.

According to HP:
"This problem is usually due to a data signal generated through the PC's parallel port during the computer?s power on self-test, or while restarting The Operating System. In most cases, the data signal being sent determines if a particular device (or type of device) is attached to the parallel port. When the printer receives a string of data that it does not recognize, it will attempt to interpret the data and assign a character for the unrecognized signal. This results in garbage characters or symbols printing on the page."

I hope this helps.

by tommyd

Sorry...the operating system is XP Professional. The printer is left on all the time - it is also a fax machine (although not too many faxes come in in the middle of the night).

by captbilly1eye

Does the situation happen following a reboot with the first print job or does it happen on consecutive print jobs following good ones with no reboot in-between?

You stated the printer is left on all the time... is the computer it is connected to also left on all the time?
If not, the information from HP would apply. At which point, the only correction is to shut down the printer, restart the computer and then restart the printer after it has fully booted.

That is what I do when I have the same situation happen with any of my HP or Epson printers.

If on the other hand, if the computer that it is connected to is also on all the time, could the situation possibly be coinciding with an interruption in power like an electrical storm? If so, the HP recommendation would also apply.

Sorry... It's kind of hard to diagnose an intermittent problem without knowing the exact circumstances that are occurring to cause this issue to repeatedly happen.

by tommyd

The computer is not left on all the time - just the printer. The garbage seems to follow good printouts and not just on initial boot up, or reboot, of the computer. It doesn't seem to be associated with a disruption in electrical power, such as a storm either.

by captbilly1eye

Were you able to solve the problem?
If so, what was the final resolution?

by tommyd

I haven't been able to solve yet. It seems to print garbage pretty randomly. It may be early in the day or sometimes in the afternoon after many other print jobs have been sent. There doesn't seem to be a common link that I can find yet. I've tried turning it off and then booting the computer up prior to turning the printer back on...still prints garbage randomly. It also is very difficult to get it to quit printing after it starts this. I go into the print queue and cancel the job. It shows to be deleting the job, but still is printing. I hit cancel on the printer and it will stop momentarilly - only to continue a moment later. I will end up turning off the printer for several minutes while continuing to try to delete the job from the print queue. It will not delete. Then when I turn the printer back on, the bad print job will disappear from the queue, and the next job in the queue will begin printing (correctly). I'm at a loss to figure this out.

by captbilly1eye

I found the following troubleshooting page through HP:
http://tinyurl.com/vuyce

There are a lot of ideas there. Any you haven't tried?

My recommendation would be to replace the parallel printer cable with a newer, shorter one.
Also... just to verify... the printer is connected directly to this computer without a switchbox or network involved, correct? I believe you implied that this is a stand-alone set up, but I just wanted to be sure since those factors would definitely make a difference.

by tommyd

That is correct. It is a stand alone setup. No switchbox or network between the CPU & printer.

Thanks for the link. I'll check it out and see if I can figure this thing out.

This discussion is closed to new replies.