Discussion Locked

Ideal Network Design

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
What is the ideal network design for about 40 to 50 workstation and 2 servers? What are the peripherals needed? What are the hardware specs from server to workstations

9 replies

by scottdouglas99

Good Question. The answer depends mainly on the location. Location is very important in designing your network, which by the way, you network should be fully planned on paper before putting anything into implementation. Generally the type of setup you describe would probably be a one or two story building/space. If you already have your workstations they will all need nics (network cards). Since you only have 40 to 50 machines, you will want all the nics to be exactly the same if possible to simplify service and hopefully save you a little money with a volume buying discount. Obviously you will need network media (generally cable). This is where both location and desired speed come into effect. The amount of interference at your location is a major factor. You do not want the electronic devices in the space causing errors in your network. This is why there are different qualities of cabling. If you feel electronic interference is minimum you would typically use CAT3 or CAT5UTP. This is generally the most affordable type of cable that is practical for you to use. If you feel there will be more interference you may need CAT3 or CAT5 STP (shielded twisted pair). You'll want to use rj45 connections.
The difficult partis choosing your router/hub/switch. This will all depend on how much you have to spend. You can get a large router with many ports or a smaller router branching off into switches or hubs. It's difficult to answer the question without further info. I hope I have at least helped you begin to think about what it takes to plan the network; and by the way as i said before, planning is the most important step.

Scott Douglas, CNA
scottdouglas99@hotmail.com
http://homes.acmecity.com/thematrix/byte/360/

by wlbowers

First thing you need to do is decide if you need to devide your client machines in to Broadcast Domains. Organize your client machines into domains by, Bookeeping, Sales, Engineering ect.

Reasoning for Broadcast Domains.
Broadcast packets are sent for a multitude of task, presence, server search, ect, and go to every device in the domain. Normally this traffic is 1% or less. In a network configuration that has a decent number of devices that 1% can at times become what is known as a broadcast storm. This is where the broadcast packets flood or dominate the network.

This can be avoided by breaking the network into domains either with routers or by using a switch for each group or domain.

Routers are program intense in nature so most people are going with the new smart switches.

The distance you have to run will determine cable. Most applications can utilize Cat 5. Noisy enviroments or long distances might require the use of fiber to connect your domains to the master switch.

This information is general to primary considerations. I would suggest going to one of the following sites to either utilize their design services or research equipment.
cisco.com
dlink.com
3com.com

All of these companies will help youdesign your system around their equipment.

Good Luck Lee

by kevin anderson

That's pretty open ended. I'll set up my Administrative Dream Network.

50 Workstations would still allow you to install Netware 5 for Small business. This will include Server operating system, Internet access (Bordermanager), Email (Groupwise),Desktop admin software (Zenworks), Webservers, etc. Basically everything you need straight out of one box. The server I'd put it on would be a DELL PowerEdge p3 800 or so with 1 Gig of RAM, and (most importantly) SCSI hard drives. By preference, I would set the hard drives up in a Mirrored set, rather then RAID 5, but there are a few other factors in that decision, and they are outside the scope of this question. I would have a Mammoth 2 (as opposed to a DLT) installed for backups, and use either Arcserver, or BackupEXEC (Don't care. Both have good and bad points.) I'd use a 3C980 NIC plugged into a CISCO Switch.

The desktops would ALL be identical DELL Optiplexes with about 256 Megs of RAM and p750 or better processors running Windows 2000. They would NOT be Small Form Factors, at least not by preference. They would use 3c905b NICs.If you weere to recieve all 50 at the same time, then have Dell preimage them for you. It's worth the $15 or whatever it costs...

Printers, etc would be HP (Laser/Inkjet), and would run off of HP Print servers.

The second server, if needed, would run whatever OS was needed, Preferably Linux or Netware, but some applications need NT, so we could do that if we needed to. In any case, it would not be a domain.

This would be the fastest, easiest, most powerful fully integrated solution available.

Kev.

by jolly roger

An alternative to Kevin's solution would be to buy/build/have built two identical servers running Microsoft Windows 2000 Server (or, if you will NEVER exceed 50 workstations, consider Microsoft Small Business Server 2000 which was released on Feb. 21). If my budget permitted, I would make my workstations Pentium 4 with 256MB RAM. This may cost a little more up front but consider how much you'll save but getting an extra year or so out of each machine. We all could give you much better info if you would share what your software requirements are (just standard desktop software like Microsoft Office loaded in each workstation or some vertical client/server application) whether you'll be sending a lot of bandwidth intensive information on yournetwork such as voice, video, or multimedia. What is your budget like. I would love to design (who wouldn't) your network knowing that there was a $250,000 budget to get it implemented with an additional $10,000 a month to maintain it.
Every element of the workstations and servers merits your attention (Motherboard, Processor, RAM, I/O slots and busses, case, power supply, storage devices such as hard disk, floppy, ZIP, SuperDisk, Jaz, CDROM, DVD, DVD-RAM, CDRW, and whether SCSI or IDE, to name a few). Consider engaging someone familiar with these subjects and the cost could easily be offset by the money you save on hardware now and in the next few years. Good luck.

This discussion is closed to new replies.