14 replies
by a. g.
I'd try making a directory called Win98 on the C: drive and copying the cab files from the Win98 folder on the CDROM. Then run Setup from the C: drive. It doesn't take up that much space on a 40 gig drive and that way the CAB files are there when you don't have the CD around.
AG
by korgmeister
if the cdrom installation didnt work after a few try, i suggest you have to install it from a hardisk. it should be working.
:)
by greysonj
by dmiles
Check the motherboard manufacturer site for any bios updates
The cd rom may not be the first boot device in bios configuration
Boot computer at startup screen press the designated key to enter bios setup
In the boot device order select the cd rom as the first boot device
Reboot,using a windows start up disk(windows98) if available,select to run setup with cd rom support,it should then run installation,also you want to be sure that you have the first partition as the active partition
by hal 9000
Does the M'Board support a drive that big?
If it doesn't and there are no BIOS updates that do you can only use a drive that size as a Slave Drive as the Maxtor Utility tricks the BIOS into recognizing the drive but when you attempt to install Windows to it the setup utility ignores the Maxtor utility so the drive effectively no longer exists according to BIOS.
If you use it as a Slave with 98 loaded onto another drive it should work OK but I very much doubt that you'll ever be able to install 98 directly onto that HDD. Of course you could always Ghost a Copy into the Default Partition and then run the Maxtor Setup Utility from there to create the remaining partitions or use something like Partition Magic or System Commander to do the same thing.
Your problem isn't with 98 but the M'Board or the way you have setup the partitions with the Maxtor Utility. If the M'Board can actually read a 120 GIG drive use FDISK to create a 40 GIG partition and then install Windows to that and then using System Commander, Partition Magic or even FDISK you can create the rest of the partitions as you want them.
Col
by hal 9000
Of course you could always add a PCI IDE Controller Card and get around that problem of th Hardware not being new enough to support the drive. That would be a lot cheaper than replacing the M'Board. CPU, RAM.
Col
by willcomp
Do what Hal9000 suggested, but first low level format drive using Maxtor's utilities and start from scratch using fdisk instead.
Dalton
by bipin002
by absolutely
I suspect that Maxtor's partitioning/formatting disk lacks the ability to make a FAT32 partition bootable, or that you forgot to do that. I would run Windows FDISK from a floppy, remove all your existing partitions and start over, being sure to make the first partition Active as well as Primary. As I remember, Windows FDISK will prompt you to make the first partition active, and will only make the first partition Primary, so you cannot go wrong.
My reading of the fine print that accompanied the Maxtor drive I bought recently suggests that there are very few situations in which they recommend that we use their software! My MaxBlast 3 CD says "Boot from this CD if you do not have Windows installed" but accompanying documentation makes (somewhat) clear that FDISK is really the way to go.
by absolutely
by absolutely
Give this a try: make sure you're using 80-conductor cables. Using 40-conductor ATA cables might cause your drive capacity to be identified incorrectly.
j/k, I saw your answer first, I did not think of the cable type as the source of the problem. It is interesting to know that it doesn't make communication impossible, just misreads the drive's capacity.
by jdclyde
Make the first partition 10 or 20 gig. I would go with the 10.
I would only load the OS on this partition then, loading all programs and data on the following partitions.
Older systems just don't like the big drives. You may end up running this as a slave with your 20 the master.
The other option is you may need to get a different disk controller to handle that big of a drive. The "promise" cards are not expensive, and work like a charm. If you want this to be the only drive, this will probably be the method you will need to go with.
by greysonj
by greysonj
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending