Question Locked

Internet Problem

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

i have WAG54G2 linksys router for DSL connection.

Week ago i have upgraded the linksys firmware Version:V1.00.19 and also installed Trend Micro Work Free business security Advanced in WinSer2003.

Every morning i have to reboot the server to access internet..

Any Advice ?

16 replies

by tobif

In the state with no internet:
Try to connect to the administrative interface of your router to see if this is possible and whether the router still has contact with the internet.

You could also try:
- Restart the router, rather than the server.
- Do a "repair" of your network interface on the server. (Deactivate, then reactivate)
- Check if there's an inactivity timeout specified in the router
- Oh, run ipconfig /all to see if there are any clues there.

by sharq.66

I tried to repair Network Interface on Server.

Found Error

Windows could not finish the repairing the problem because the following action cannot be completed: Clearing the ARP cache

by tobif

That's not the root to the problem.

And, my idea was that you can try this action when your internet connection is down, in order to see if that helps it to get started.

Since your problem happens only once a day, your search may take a week... Right now, we don't even know if the problem is in the router, on your server or even at your provider.

by ameack

I would suggest to Disable Trend Micro for a day and test it.
Also look out for your DSL connection for any dropout, check logs in the router for PPP connections.

by sharq.66

I face this problem any time...may be twice a day, once a day or may be in two days...but it happens every now and then...and i have to reboot the server to access internet..

In my router webpage DSL, Gateway, Wireless and lan evrything is showing up and working

by tobif

Then it could be:
- Some NAT or firewall issues
- DSL PPP-session timeout
- Problems with DNS (DNS settings or with the server itself)

Does your router create any log?
Does internet also come up again if you just reboot the router (leaving the server running)?

by sharq.66

I tried to reboot the router but faced the same problem..i have to reboot the server to get the internet connection.

My router doesn't create any log...

by luisantia

1. I have a similar problem in the past, i update Nic driver problem solved.

2. Disable Trend Micro might be a software problem

by sharq.66

i upgraded NIC firmware...still same problem...

I have to disable/enable Network interface to get the internet access

by tobif

You no longer need to reboot. :)

In this locked state, can your computer still reach the router?

Have you tried disabling Trend Micro?

by tobif

Command window and run the command
ipconfig /all
The information there may give some hints.

By the way, while you're without internet at your command prompt, try to ping a google server, like this:
ping 72.14.204.103

And then, like this:
ping www.google.com

The information you gather this way can be very useful in pinpointing your problem.

by sharq.66

Tried disabling Trendmicro...

nothing works...

when the internet is down i can access the router webpage...

any further advice

by tobif

Since you can access the router, your IP routing works.

This means that the problem is either the router dropping connection to the internet, or some problems with dns.

So, next time:
Try the pinging I described in an earlier post (to www.google.com and directly to the corresponding ip address). If "pinging to numbers" works, then we need to drill deeper into dns settings.

Also check the status page on your router. Does it tell you anything about the internet connection status?

by sharq.66

I will ping the google as u asked me to do...

whenever the internet is down...the DSL connection, Gateway, LAN, Wireless all are showing up....

and one more thing...

whenever i try to repair network interface i got an error clearing arp cache....

i flushed dns from commond prompt and also deleted the arp cache

by tobif

ARP is used to bind ethernet MAC addresses with IP (dotted) addresses.
And, as far I can see, that works.
The error could depend on mismatch due to partial support for IPv6, or different authority levels (where ARP is very low in the protocol stack - close to the system core).

By the way, IPv6 could be involved in this, one way or another. If you don't use it and your ISP doesn't support it, you might be better off unchecking IPv6 in your list of networking protocols...

Anyway, we'll wait and see.

This discussion is closed to new replies.