Discussion Locked

IP6 / IP4 interoperability

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

hi all,

Has anybody here implemented an isolated IP6 testing environent within an existing IP4 LAN? Basically, I'm implementing an IP6 development area where I can test multiple Unix, Windows, Linux clients using single / dual stack IP4/6.

I already have an isolated scenario, which is basically an isolated Cisco switch (we're a Cisco house) , but I'd like to give my user base the ability to copy code etc.. to the IP6 area, and also provide them access to DNS AAAA records, DHCP 6 etc...

If anybody would like to make any suggestions, or quote from experience, I'm all ears.

I am toying with the idea placing a dual homed Linux box in a firewall roll between both Lans, or using an old Cisco 1700 router to manage the routing, although I have not arrived at any IP4-IP6 address translating strategy as of yet.

Ciao

BH

5 replies

by zontago

Hi, I do think that I understand IPV4. The rules should generaly stay the same excluding the classes. But I'd bet that you will need two interfaces on a device - i.e. a router of a PC - for routing between IPV4 & IPV6.

Keep us posted!

by bennyhell

I got this working using a Cisco 2600, IOS 12.3(22)

Basically, I have one NIC of the 3600 on the IP4 side, one on the IP6 side, which connects into a dedicated Cisco switch, which all the IP6 servers also pacth into.

I successfully configured NAT-PT, using v4v6 and v6v4 static NATs, along with dynamic NAT for IP4 to IP6.

SAMPLE ROUTER CONFIG:

ipv6 unicast-routing
!
interface FastEthernet0/0
ip address 10.5.10.1 255.255.255.0
duplex auto
speed auto
ipv6 nat

interface FastEthernet0/1
no ip address
duplex auto
speed auto
ipv6 address 2001:CC1E:1:3::64/64
ipv6 enable
ipv6 nat
!
ipv6 nat translation udp-timeout 600
ipv6 nat v4v6 source 10.2.2.49 2001:CC1E:1::A02:231
ipv6 nat v4v6 source 10.5.10.10 2001:CC1E:1:3:203:BAFF:FE6F:3E91
ipv6 nat v4v6 source 10.5.10.11 2001:CC1E:1:3:203:BAFF:FE66:240B
ipv6 nat v6v4 source list ip6list pool v4pool
ipv6 nat v6v4 source 2001:CC1E:1::A02:231 10.2.2.49
ipv6 nat v6v4 source 2001:CC1E:1:3:203:BAFF:FE66:240B 10.5.10.10
ipv6 nat v6v4 source 2001:CC1E:1:3:203:BAFF:FE6F:3E91 10.5.10.11
ipv6 nat v6v4 pool v4pool 10.5.10.20 10.5.10.200 prefix-length 24
ipv6 nat prefix 2001:CC1E:1::/96
!
!
ipv6 access-list ip6list
permit ipv6 2001:CC1E:1:3::/64 any

-----------------------------------

Obviously the IP addresses of some of the IP6 servers are:
2001:CC1E:1:3:203:BAFF:FE66:240B
2001:CC1E:1:3:203:BAFF:FE6F:3E91

Useful Cisco commands:
sh ipv6 nat translations
sh ipv6 nat statistics

Best regards,

BH

This discussion is closed to new replies.