Discussion Locked

IPX Router Error

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm running two Novell 4.11 servers, one here and one across town. I'm only getting the message on the one server here.
I looked at Novells website and tried everything, I can't get this resolved.

3-26-01 9:04:33 am: IPXRTR-6.60-175
60:15.630779 Router 020000000011 on circuit CPQNF3_1_E82 claims network 00000001 should be 00000002.

I reset all JetDirects here, I reset all routers here, I typed reset router at the Novell prompt serveral times. How can I track this down. Is the 020000000011 an ID number of some kind. I looked on Novell website and it has a list of Manuf. IDs, but the first six digits (020000) are not listed, I'm I looking at this wrong?

Thanks

5 replies

by estebandelatorre

This is a configuration error.
The id that you mention may help you to identify the manufacture. I've never heard about 02...
How to identify it, is the question...
Issue a "display servers" at the console prompt and find the mac address beginigwith "02...." If you find more than one, you have more hardware of that kind in your network!
Another data is that you have the segment and frame (ETHERNET 802.2) that is causing the error (CPQNF3_1_E82).The number near the display servers screen represents the number of hop's that the hardware is from you.
Number 0, the hardware is ON the server. Your (This) server should have 0 and may appears many times here, one for each service that it holds.
Number 1 the hardware connected to the first (main) switch or hub where the server is connected.
Number 2 The hardware is connected to a hub or switch that is connected to the main switch or hub, and so on.
If from the main switch you have 10 hubs connected, disconnecting one by one, waiting for a few seconds and issuing a Display servers command at the console prompt (until it dissapears) will help you to isolated the hub or switch where the conflicting hardware is, then do the same but port by port.
Depending on what you find, is what you should to to fix it!
This should be more easy if you have a management software for your switches and Hubs...
Good Search !!!

edt@bancobgn.com

by stngfan1

I did the display command and nothing came up with that number. I looked at both servers.

by jimbb

Your network-card and something on the LAN don't agree on the right IPX number. I don't know how much you know about this, so some here may not be new to you.
When you "bind ipx to...", the "net=" number should be the same per segment, per frame-type, for all nodes. If there is a router between here and "across town" that splits up your network, there should be a different "net=xxx" number over there, for each frame type.
If this is already the case, most likely some other box (a router, a printserver,...) has been moved, or your network config has been changed, and that box assumes it is still in the old situation. You can look up the manufacturer of a MAC address at sites such as http://standards.ieee.org/regauth/oui/index.shtml, but yours looks like a user-defined address, so it won't help.
I would suggest to type "config" at each server prompt, and note the "LAN Protocol" info per NIC, for each frame type, and compare. There too you can see the "Node address", maybe your offending card is there. Make sure your IPX network # is unique where it should, and the same where it should. To me this sounds like some network card in a server, no jetdirect or so, generally they have non-adaptable addresses, like 080009..., 0080A0..., or 00306E...

Jim

by stngfan1

These are the settings for each server.
Server1 Server2
IPX#35454021 356345BC
802.2 00000001 802.2 000000a1
802.3 00000003 802.3 000000a3

This discussion is closed to new replies.