Discussion Locked

IRQ and PCI.Conflicts-Help me!!

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

This is how conflicts appear in my system info tool:
IRQ 5 Intel(r) 82810 Graphics Controller 4.12.01.2586
IRQ 5 ACPI IRQ Holder for PCI IRQ Steering
IRQ 9 Intel 82801AA USB Universal Host Controller
IRQ 9 HSP56 MicroModem
IRQ 9 CMI8738/C3DX PCI Audio Device
IRQ 9 ACPI IRQ Holder for PCI IRQ Steering
IRQ 9 ACPI IRQ Holder for PCI IRQ Steering
IRQ 9 SCI IRQ used by ACPI bus
IRQ 14 Primary Ultra ATA Controller
IRQ 14 Intel 82801AA Ultra ATA Controller
IRQ 15 Secondary Ultra ATA Controller
IRQ 15 Intel 82801AA Ultra ATA Controller
The above list is what is happening with my PC runs Win98SE,and i have internal modem,camera(USB),scanner(USB,mouse(PS/2),keyboard,printer.
It has Intel 810 onboard chip,1HDD,1DVD player,1floppy,128 SDRAM,CELERON 656
The microphone as soon as the modem dials out,records something that seem to be playing in double the normal speed.The result is i can not use the mic to speak to people in Netmeeting,or any other software that offers internet phone capabilities.
When i am off line,the mic records normally.
This is how the IRQs appear in sustem info:
0 System timer
1 Standard 101/102-Key
2 Programmable interrupt controller
3 Communications Port (COM2)
4 Communications Port (COM1)
5 Intel(r) 82810 Graphics Controller
5 ACPI IRQ Holder for PCI IRQ Steering
6 Standard Floppy Disk Controller
7 Printer Port (LPT1)
8 System CMOS/real time clock
9 Intel 82801AA USBUniversalHostController
9 HSP56 MicroModem
9 CMI8738/C3DX PCI Audio Device
9 ACPI IRQ Holder for PCI IRQ Steering
9 ACPI IRQ Holder for PCI IRQ Steering
9 SCI IRQ used by ACPI bus
10 MPU-401 Compatible
11 ACPI IRQ Holder for PCI IRQ Steering
12 PS2 Pilot Mouse Wheel Scroll V1.0
13 Numeric data processor
14 Primary Ultra ATA Controller
14 Intel 82801AA Ultra ATA Controller
15 Secondary Ultra ATA Controller
15 Intel 82801AA Ultra ATA Controller

19 replies

by ann777

Get your modem OR the PCI audio device off of IRQ 9 and place one of them on IRQ 11. The ACPI IRQ Holder for PCI IRQ Steering's are fine at 11 and should not cause any resources issues with either the modem or the sound card.

The way to do that depends entirely on your system bios... who manufactured your BIOS and when you enter into the setup screens, what do you see as far as resource allocations? Usually they are in the "Advanced" settings. Do you have a manual that came with your motherboard?

by shanghai sam

Thanks for your response.I should make clear that i have onboard graphics,sound and modem,not separate cards.Therefore the solution you suggest is not applicable.When trying to change settings for modem through system properties,it is impossible.A message saying "You can't change these settings " comes up.Also there is a message about DOS applications ,need to have the resource settings changed.
I asked the motherboard manufacturer and they suggested flashing the BIOS,i did ,bnothing changed,even with the updated BIOS.What puzzles me is that it works OK when off line.Maybe a way to change onboard chip's settings???Do you know how?I can't find info anywhere on that and i am no IT profesional,so.......
Is normal that the ACPI for PCI IRQ Steering appears on 11, 9 and 5 ?
Also what is the :SCI IRQ used by ACPI bus for?i dont have any other devices appart from those mentioned in previous posting.And even without camera and scanner the same thing happens.

by george

I should add that i have no cards installed(graphics,sound,modem),only the Intel 810 onboard chip that includes all the above(i think)
Please note that certain entries appear up to 3 times,with no reason(ACPI IRQ Holder for PCI IRQ Steering for example)

by scviking

The problem you're having with setting the IRQs can be solved by setting each device's IRQ in the BIOS. You can usually access the BIOS setup utilities hitting the key when booting the computer.

Now the fun part- you'll need to juggle around quite a few IRQs to get this system to work.

First off- don't worry about the IRQ Holder for PCI IRQ Steering entries- they're supposed to be there. Ignore them completely.

Do you use COM 1 or 2 (yes if you use a serial mouse)? If not, disable them first. This will free up IRQ 3 and 4

Do you use a PS2 mouse? If not, disabling this will free up IRQ 12.

Normally, your display adapter (video card) resides on IRQ 11. It's free, so switch video to that IRQ. This will free up IRQ 5.IRQ 10 is usually NIC card or sound card, in that order. Right now, the MPU-401 entry suggests that some of your sound card hardware is installed on IRQ 9 and 10. Yank it from those IRQs and set the onboard sound to IRQ5, both for the MPU-401 deviceand the PCI audio device. If you don't have a network card, you can set the sound hardware to either IRQ 5 or 10.

IRQ 9 is your big culprit. You need to clear it out completely except for the IRQ used for PCI bus.

If you disabled COM1 or COM2,move the modem's IRQ to one of those IRQs (IRQ 4 for COM1 or 3, IRQ 3 for COM 2 or 4).

Did you disable the PS2 mouse? Probably not- I'm assuming you actually have a PS2 mouse and not a serial one. If you have a PS2 mouse, try moving the USB controller's IRQ to the other COM port's IRQ (you don't need a COM port for a serial mouse if you have a PS2 mouse).

If you have a serial mouse, set the USB controller's IRQ to 12.

Good luck. I hope this helps out a bit.

by scviking

The idea here is to get the IRQs of your onboard devices close to what they normally are. Here's a quick list:

Serial mice are usually on COM 1, IRQ 4
PS2 mice are almost always IRQ 12
Modems usually occupy COM 2 or 4, IRQ 3
Video cards usually use IRQ 11
Sound cards are normally IRQ 5
Network cards are normally IRQ 10

USB adapters can be almost anything, but they will normally replace one of the above devices and you can use the corresponding IRQ for that device.

IRQ 9 is a cascade controller linked closely to IRQ 2. Normally, it's the last one you want to fill up, but things like the ASPI PCI controller should be OK there.

Have fun!

by scviking

One last note:

Once you get the IRQ conflict fixed (and you will, don't worry!) you'll need to juggle some settings around in Windows.

You may need to uninstall/reinstall your modem, video and sound card drivers, for a start. The rest should configure themselves automagically.

If the above procedure doesn't work, take the box into the shop......

by donmars

I IRQ steering is your problem, try disabling it as outlined below or fix it. you will find your answer here, paste this address in your address box.

http://support.microsoft.com/support/kb/articles/Q182/6/28.asp

This a cut and paste. you should go there for alot more info.

To disable PCI bus IRQ steering:

Click Start, point to Settings, click Control Panel, and then double-click System.

Click the Device Manager tab.

Double-click the System Devices branch.

Double-click PCI Bus, and then click the IRQ Steering tab.

Click to clear the Use IRQ Steering check box, click OK, and then click OK again.

When you are prompted, restart your computer.

NOTE: You may also have to disable PCI bus IRQ steering in your computer's BIOS. For information about how to do so, contact BIOS MFG (or go to ADVANCED CMOS SETUP and disable it)

The following settings determine which routing tables Windows uses when programming IRQ steering:
Get IRQ table using ACPI BIOS:

Whenthis check box is selected, the ACPI BIOS IRQ routing table is the first table Windows tries to use to program IRQ steering. If a PCI device is not working properly, click box to clear it.

Get IRQ table using MS Specification table:

When thischeck box is selected, the MS Spec routing table is the second table Win tries to use to program IRQ steering.

Get IRQ table from Protected Mode PCIBIOS 2.1 call:

When this check box is selected, the Protected Mode PCIBIOS 2.1 routing table is the third table Windows tries to use to program IRQ steering.

Get IRQ table from Real Mode PCIBIOS 2.1 call:

When this check box is selected, the Real Mode PCIBIOS 2.1 routing table is the fourth table Windows tries to use to program IRQ steering.

NOTE: By default, the Get IRQ table from Protected Mode PCIBIOS 2.1 call check box is not selected. You should select this check box only if a PCI device is not working pr

by donmars

IRQ Steering is a great Windows feature but I think you have a conflict with its configuration. You can solve this by learning what it is and making the corrections to it in Wnidows and/or BIOS setup. I would guess that the setup in Windows itself is conflicting with the setup in the BIOS or visa versa. You can attempt to fix it or disable it and manually configure IRQs'. IRQ steering automatically attempts to assign IRQs'. Its needed for real Plug n Play. After you do this you will have learned something important in Windows config, If you are that type. I think its fun.

by jaboy78

To tell u the truth, i never heard there got celeron 656,only 667. maybe u set wrongly to cause this problem or your motherboard cannot support win98se..
try win95b first. if it is ok, means that ur pc really cannot support win98se

by macros

I don't see that this is neccessarily an IRQ problem. I suspect it's an audio device problem...with the modem and mic (or something else) requiring resources. Don't know specifically what the solution is though.

by macros

I don't see that this is neccessarily an IRQ problem. I suspect it's an audio device problem...with the modem and mic (or something else) requiring resources. Don't know specifically what the solution is though.

This discussion is closed to new replies.