Discussion Locked

ISP Modem Connection Problems...

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi all:

I just signed up with US WEST as my dial-up ISP. I'm an Internet developer, so I need a reliable Internet connection, but I'm definately no hardware guru. I have been having problems getting US WEST's dial-up number to answer. My modem would call and call and would get no response. I called their tech support and they said my modem was on their "problem" list. I have a Conexant SoftK56 Data, Fax, Speakerphone PCI Modem #2. The tech support people had me add this line to the "extra settings" field under the advanced connection setting for my modem: +MS=V34. I take that to mean that my modem is emulating a V34 type, which has a top connection speed of around 34,000 bps? Adding this info now means that I can connect ok, although only at 28,800 bps. My question is:
1). Should I get a new ISP?
2). How does their server even know what kind of modem I have before it picks up the incoming call?
3). My old ISP had no problems with my modem and I got connection speeds of about 44,000 bps. Why

14 replies

by logic2 tech

First, what are you paying for? My ISP provides 6 different services, BASIC = 28.800 connection speed. NEXT = 56k connection w/ dedicated lines for no busy signals. Higher is mostly for business networks.
If you paid for a 56k connection, I woulddefinitely look around for a more reliable ISP.
2. When you dial your ISP, your modem and the server modem 'talk' to each other and determine the best ways to communicate w/ each other.

With my service, the 56k w/ dedicated line, I have never had a connection of less than 49333bps and frequent 50666bps
Hope this helps some,

Logic2Tripper

by thegothicedge

Greetings,

I would first look around for a better ISP, alot of times I find that the help desk at some of these ISP's read your answer from a script and that they state that its on their "problem list" means that they don't know how to fix the problem. If you have paid for a 56K connection then by all means you should be running in the range of 44000 to 52200. I have a small ISP where I live they offer regular and DSL, and I have a Zoltrix 56K modem myself and I connect from anywhere between33600 to 52200, so when I make a connecting of at 33600, I disconnect and reconnect and get around 49000 or so. But if is preference really. However I would recommand getting another ISP which covers a wider range od modem speeds.

by ec364

If you had no problems with your modem connection to your former ISP and at 44,000bps(!), why did you change? One could hardly obtain that dialup connection with 56K modem!

I don't know how much you're paying your ISP for dialup connection but ifDSL is available in your area, I would highly recommend to subscribe to it. Especially you, who is an Internet Developer. A lot of DSL ISP offer from $39.95 to $49.95/month for a 640KB connection (thats 640,000bps!). I knew because I am using one (BellAtlantic.net). It's well, well worth it!

Anyway, if DSL is not available in your area, I highly recomment EARTHLINK.NET. Very reliable. I have been using this ISP for my dialup until I moved up to DSL.

Enjoy!

by hozed

First, V.34 does not mean 34,000 bps. V.34 is a modem standard that specifies a connection of up to 33,600 bps. Most people tend to get 28,800 bps connections with these, so that's normal.

Second, the reason for your problem is simple..... yourISP's modems don't like yours. I've had this problem several times. I have a Diamond SupraExpress 56e. With a local ISP, I could connect, but would be kicked off for no apparent reason after about 5 minutes. Dropping to V.34 didn't help. I had the same problem with Qwest and WorldCom dialups. On the other hand, I have always had good luck with EarthLink.net. I usually connect at 49,333 bps.

Third, your options are limited since its highly unlikely that your ISP is going to buy new equipment just for you..... buy a new modem that does work with your ISP's equipment or find a new ISP.

by jeff

I have the same modem you have, I connect to Prodigy Internet, and I always get a connection of 49333bps or 50666bps, I usually use the service 200+ hours a month and being a national ISP, I can connect in most areas in the country. I would ditch USWest and look into a new ISP or if you can get it, go for broadband. I have a microwave connection at work running 3-4 mbs for about $80.00 bucks a month. I wish I had it at home ; ). From what I understand their servers need to perform a "Handshake"with your computer, and if they can not resolve a connection with your modem you get disconnected.

Hope this Helps,

Jeff

by Former member

This is likely to be lengthy. If you have any questions, feel free to mail me: discorcia@home.com
Before you jump to another ISP, try the following:
1. Get your phonelines tested for line noise. US West Telecom's area is subject to a lot of staticy phone lines from my ISP days. Be sure to specify the number you're having issues connecting to. Test the theory yourself by asking USWEST to give you dialup numbers for a nearby city, or somewhere that's an LD call. If that connects clear, then it's your local phonelines. If not it's likely lines close to your house, something in your system, or the performance of your modem. (Could be different server-side hardware which doesn't like Rockwell chipset modems much. It's a pretty common issue.)
2. Make certain you are on the current drivers for your modem.
http://members.cnx.net/reboot/modems/
3. Go to Dialup Networking, create a clean dialup connection. Go into the connectio properties|server types, uncheck everything except TCP/IP. Remove the

by Former member

Whoops.
remove the init string and try again.
4. Go back into the connection properties, hit 'configure' and lower the port Max Speed to 57600. Click on the Connections tab and hit 'Port settings'. Lower them to 2,3 instead of 3,4. Try connecting.
5. Go back into the connect properties|
configure|advanced and disable 'compress data'. Try connecting. Go back in, recheck it, try switching flow control to Software. Try both changes together. In Extra settings, try AT&F or AT&F1 or AT&F&C1&D2S=50. If you get strange errors, pull the string out, reboot if necessary to clear it.

This discussion is closed to new replies.