Discussion Locked

Linksys Router - DHCP address to NAT ???

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a Cox cable connection. A friend of mine who has the same type of connection told me he recently set up a home network with a Linksys WAP11 wireless router. He used NAT to translate his "DHCP" acquired address from Cox to his PC's.

I thought it was only possible to do this with a static address. He also said that, if he wanted to, he could install a hub or switch in port 1 and theoretically have about 250 addresses. (obviously that would not be wise)

He said he'd provide me with the configuration for the router once I purchase it but I'm still skeptical. Can anyone provide me with the code for the configuration as well as an explanation as to how this is possible? Assume I'd have 2 directly connected PC's and 2 laptops connected via wireless NIC.

Thanks,
Dave

8 replies

by pschuvie

Well all of this is very much do able, doesn't really involve any black magic or voodo, and just reflects the improvements due to standardization and incorporation of more features into a single box, if you will. Remember your talking about a Router with intelligence built in not just a simple hub.

No, the ip address no longer needs to be static. Some old routers may have required it but the limitation of available ip addresses has made that impractical and therefore improvement to accept either static or dynamic ips is built in.

Also the router has built in its own NAT/DHCP server so it can either accept static Local addresses or issue dynamic addresses to all members of the local lan. Use of static or dynamic on the local side is much debated when it comes to both troubleshooting and security, particularly when wireless is involved, but it is only a decision you make during the setup stage of the router. A local lan with a wireless element issuing DHCP ip addresses could mean that your neighbor could tap into your local lan by simply setting up his wireless computer to accept a DHCP address. There are other security elements that handle this but that is a simplification of one concern. When you want to control the lan and you only have a few member units static local addressing is often seen as a better approach. But that is a whole big topic by itself.

So there probably shouldn't be any reservation on the Dlink unit in general as it will do just what your friend indicates. Also, I doubt that he has any magic formula, maybe a few tweaks he discovered, but probably more not wanting to get into fine points and options until your ready.

by pschuvie

(Finishing)

I will add that one nice feature of most DLink routers is the ability to "clone" a mac addresss. Basically this feature makes the device address (mac) of the Router look just like the one that was your NIC card in the original cable connection. It has to do with how some cable operators "keep track" of whether or not your running a network or mini isp through one connection. After all they want to sell you more and if you were running those extra 250 computers they would be losing money. Again it is explained in the instructions.

As to expected configuration, it does depend on the specific model that you are considering. With the most basic unit you would go cable modem to Router Wan, 1 PC to the LAN port all other units via wireless with appropriate wireless cards installed in each. With the Router/Switch models you have a couple more ports for the stationary PCs to use and they can be set with 10/100 NICS for better local transfer and again the Notebooks withwireless cards installed.

Lastly, there is a lot of very good information available at the DLink site and I would suggest you spend some time there looking things over. Don't be afraid to download some of the manuals and look them over and getyour questions up front before you buy.

One last note, wireless cards can at times be fussy between mfgs, where possible try to make everything one brand.

Hope this helps and answered your questions completely enough, if you need more post a comment.

by donnie.schexnayder

I use a Linksys router with an Adelphia cable connection. I get my WAN IP address from Adelphia using DHCP (definitely NOT static, although it rarely changes)...the router then "NAT's" the Internet connection to my internal LAN. It really works...you can have DHCP working on both sides of your connection. And all for only $75 bucks :>)

by Former member

All of this you described is do-able, and actually many ppl do it. Te DSL/Cable router gets a public IP from the ISP, while the router gives your PC private addresses that are then translated (NAT'ed) on the router to the one public address. All highly do-able and required if you want more than one PC on the Internet at one time.

This discussion is closed to new replies.