Discussion Locked

Linksys Router Setup with Small Network

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a Windows 2000 Server and about 10 computers running NT, 2000, and 98. I also have a cable modem with dynamic addressing. I have the server running DHCP server also and the scheme of addresses is 10.0.0.X with a subnet of 255.0.0.0. I am trying to set up a Linksys BEFSX41 cable/dsl firewall/router but the only options I see are for different subnets like 255.255.255.0 and others, but not mine. Also, everytime I try to change the ip address of the router from 192.168.1.1 I can no longer access the setup program in the router. Can my network computers see the router if I keep the 192.168.1.1 address? What subnet would I need to keep in the router? Would I then make sure the computers all have the 192.168.1.1 address for their gateways? Please tell me your suggestions with this hardware. I know a real roouter like Cisco is better and has more options but this is all I have to work with.
Thanks.

8 replies

by bohicam1

If you change the router address to 10.0.0.1, are you trying to access its interface by typing in http://10.0.0.1 ?
Alternatively, you can change all of your computer addresses to the 192.168.1.X range...you only have 10 computers on the network and this range will allow you up to 253 nodes(excluding the router)
You can use the router as the DHCP server, just configure it to give out the addresses instead of your server.
Good luck!

Mike

by cg it

To answer your question "can my network computers "see" the router if I keep the 192.168.1.1 address" . That depends upon what you mean by "see". I assume what your question is, is how do you setup your Network properties on client computers [LAN] to use the Linksys router as the gateway to the internet. If that is your question, there are two ways. Static IP and using a proxy server. From your question, it appears that your trying to setup you LAN using at static scheme [by specifing the gateway address [your router] on client computers, yet you have DHCP services running on the LAN. It probably would be a good idea to use a static IP addressing scheme [you have only 10 clients which is a relatively small # to track IP addresses]. That way, you can leave DHCP off on your server, assign an IP address to each client [including your subnet mask you wish to use] specify the gateway IP address [your router IP address] and way you go.

Using DHCP on the router is a pretty good idea if you don't have a statically assigned IP address from your ISP [IP addresses from an ISP can change "whenever"]. There really isn't any reassigning to do on the router in terms of IP or submask ] The Router acts as an independent [for lack of a better term, "server"] that negotiates with your ISP via "send discover" to obtain an IP address for your network and then makes the connection[which is "always on"]. Your clients then "USE" the router's connection to access the external world. Clients don't actually "connect" to the router, [your server is the only actual connection] rather they "access" or "use" the router's connection as a "gateway" out.

by cg it

My suggestion of setup assumes that your clients ARE NOT directly connecting to the router, rather they are connected on the LAN side via a hub or switch which connects to the W2K server. The W2K server is the only computer actually connected to therouter.

If you wish to NOT have to assign IP addresses [and submasks] to clients on the LAN and want to use DHCP for that, I suggest that you go the route of a proxy server that clients will use for external acess. That way, you don't have to statically assign IP, Submask, and gateway addresses on client computers [good way if you have ALOT of clients]. The proxy server then is configured to use the external interface [usually a second NIC] as the "gateway out" and clients web browsers are then configured to use the proxy server. The proxy server [or "gateway" server, which the W2K server will acts as] then "uses" the second NIC that is connected to the router for external access. Either way, a good firewall is needed to keep the LAN secure [I wouldn't rely on the DSL/Cable modem firewall].

by currera501

I am running about the same setup,but I am using a Linksys BEFVP41 which is about fourty dollars more and is hardware driven instead of software driven. I don't know much about the BEFSX41 I do know that the BEFVP41 is real easy to setup and the router's address is 192.168.1.1 which any pc on your network can see. And if you want to change it all you do is type in 192.168.1.1 and go to the setup page and change the address and the subnet, just that easy.

This discussion is closed to new replies.