Discussion Locked

Loss of video signal in DOS and D3D

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My system configuration follows:

M/B: Azza PT-5VMD
CPU: AMD K6-2 450 Mhz
Memory: 64mb 168 pin DIMM
Bios: Award
Sound: Creative Sound Blaster Live! Player 1024
TV: Pinnacle PCTV Rave
Graphics: Creative 3D Blaster GeForce 2 MX

I have had no problems with the GeForce 2 so far, but I booted up the computer this morning and there was no video signal. The monitor worked fine but did not display anything. It was not until the computer had finished the bootup process and was in Windows thatI could see anything. This was achieved by switchig the monitor off and on. The signal then slowly appeared.

I tried too access a full-screen MS DOS window so I could do some command line functions for one of my programs, but as soon as I opened command.com the video signal was lost again. I had to Alt+Tab back to the Desktop and again switch the monitor off and on again to get a signal back.

I tried playing Unreal Tournament, and the same problem happened.

I tried playing a 2D Dos Game, and the same problem happened.

Any program that runs in the Windows environment runs without any problems. Once i try to run a program in full screen mode, like a game or DOS, I lose the signal. Not once has the computer locked up when I lost the signal, and in each case I could get the signal back by Alt+Tabbing back to the desktop and switching off and on the monitor.

Creative Technical Support were, as always, inherently ineffective, suggesting that I enter my BIOS and change some settings, but as I cannot access the BIOS as I can't see anything until the PC enters Windows, this is not much help.

I would greatly appreciate any help on this matter. I have very little funds at the moment, so I would like to try and solve this problem without the purchase or replacement of any hardware if possible.
Thanks very much in advance
-Marc Piano

7 replies

by freetech

there are afew things that may be wrong. here's a possible solution that'll be free. re-install the card's bios. it should be available from the card manufacturer. a reference bios should be available from the nvida site. this should be available through your windows interface.
next step. try to slow down your card's agp speed to 1x. unfortunately, this may only be possible through the BIOS settings on your mobo.

by mapp84

Thanks for your advice, but unfortunately I cannot flash the card BIOS as you need to be in pure DOS to do this (apparently). Since I lose the signal as soon as I enter any form of DOS in full-screen, I cannot do this. Thankyou very much for trying to help me.

by dmiles

It could be a driver problem,go to manufacturer site and get the latest driver for the card.
Boot into safe mode at startup and trouble shoot the problem from there.
Also look at the game manufacturer site to search for any issues listed concerning the game and video card type.

by mapp84

It couldn't be a driver problem as there is no signal at all from bootup until it enters Windows. Since it doesn't use drivers when initiating the BIOS etc, I assume it's not a driver problem.

Thanks anyway

by richard_barsby

Hi The problem I believe is the vertical refresh setings for the 640 x nnn modes this card allows vertical refresh upto 200Hz and unless you have a very new large screen monitor you will not see anything, this may even happen in safe mode, your problem is being able to view the picture to make changes. Windows only allows 640 x 480 as a min but the card during pc boot does 640 x 350 for the very first part of pwr up then switches to 640 x 400 before windows drivers take over an set your chosen monitor type. Try setting the res to 640 x 480 in windows the set the refresh rate to adapter default this will tell the card to run 640 x nnn modes at the lowest vertical refresh setting. if you cant see the picture wait until the pic returns then change monitor type to standard VGA and repeat above then switch back to your monitor type.

Best of Luck

Rich

by mapp84

Yes this is definately the source of the problem. Now i need to know how to about fixing it!

This discussion is closed to new replies.