Discussion Locked

Low Level Formating

0 helpful
54 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a user who asked me about low level formating his hard drive. I haven't worked with that utility for a long time. My ? is, where might I find a utility to do this. Or How might I create a floppy disk to have this option.

Thanks You,

mike

54 replies

by alee100

I have used the fdisk application on a Windows 98 startup disk to format floppy drives.
Hope that helps.

by hannibb

Most times low level formating is done at the factory, it is not recomended that users do low level format since it might damage a hard drive I had a computer that came with a CD-ROM it included an utility for low level formating but warned 'do it at your own risk"

by joe hardstaff

There are usually two possible ways for low level formatting a hard disk drive. If your BIOS supports it there may be a low level formatting option in there, I would not recommend using it though, it can cause some problems (ie stuff the HDD) Go to your drive manufacturers web site, there should be suitable tools there. this page http://www.seagate.com/support/kb/disc/low_level_ata.html explains all about low level formatting, and provides a link to a low level formatting tool.

Cheers - Joe

by drvms

Fdisk is not a low level formater If your HDD developed any bad sectors dont try fdisk
or format frequently If your HDD is 10gb or above U can make partions to store data more safely and every manufacturer provides their disk manager
try fdisk after thinking 2 times
Ok Thank U
reply drvms@md5.vsnl.net.in

by tnguyen

I agree Fdisk is not a low level format utility. If your question is regarding to IDE hard drive then use CMOS built-in to low level format your drive. However, IDE is not recommended to be low level format (should check with the IDE hard drive vendor). If your question is about SCSI or MFM or RLL drive. I do not think MFM and RLL is in storage technology any more. Anyway, Lowlevel format of these drive will based on the SCSi controller or you mut know the DEBUG command and issue certian I/O address such as g:c500 for a MFM and g:c800 for a SCSI. Again, LowLevel of IDE is not recommended cuz IDE do not have Multi Level seeking of the drive themself.

by wmusil

Not sure if anybody discussed this in detail. Low level formatting is always done at a bios level from the controller. With SCSI controllers, it is usually an option available in the SCSI bios utilities. With IDE controllers, the program is residentin the bios. It is different for different chip sets but based 'loosely' on the original western digital low level utility (don't kill me here, WD ESDI is as far back as I go). To access this program, you need debug.exe on a boot floppy. You need torun debug with the proper memory address and offset of the IDE bios's low level format utility ('debug g=E800:0' BOGUS example). The manufacturer may or may not tell you but they know. Some still offer a software program on disk or CD to access the bios for you, but it is the same function. The likelihood is that if you need to low level, your drive, it is toast. You may need to low level the drive in the following circumstances. 1. There is damage in the boot sector, and the drive's sector re-mapping cannot handle it. 2. The bad-block table for sector re-mapping has filled up. 3. Drive was originally low-leveled with a non-standard CHS translation and cannot be accessed with a standard controller.
All of these usually mean that the disk is bad. Most drives have intelligent error recovery 'on-drive' and work properly for their entire life. Custom translation just doesn't happen anymore (was commonplace on older ESDI and SCSI systems).

by comptech3

I agree with wmusil on this. However, there is a DEBUG script that can be run that will remove the partition structure without damaging the actual low-level formatting of an IDE hard drive. The script can be found at : http://support.dell.com/us/en/kb/document.asp?DN=TT1011054

I find it hand to remove an NTFS partition from a drive without resorting to the NT boot floppies or other utilities out there. It is also handy to kill boot sector viruses that may be suspected to exist (be sure your boot floppy is write-protected). But be advised that any data on the drive WILL BE LOST!!!

I had customers call me for a hard drive replacement because they would get an error while formatting. I would have them run this script and Shazam!!!! The drive would accept a full format.

I would never subscribe to low level formatting on an IDE hard drive. I am also of the opinion that if the situation calls for fooling with a low-level format, the drive is most likely beyond hope anyway.

by tdad5515

I have found several hard drive manufacturers that have a low level format utility on their web page. EZ-Drive is the manufacturer and they customize the utility for the mfr of the hard drive.

by arent

Low-level format:
The sector identification on a disk that the drive uses to locate sectors for reading and writing.
Today's IDE and SCSI hard disks are low-level formatted at the factory.

From an email:
Dear Maxtor Customer:

You are correct in that formatting the drive doesn't touch the MBR which is
where ez bios is residing. What you want to do is download and run powermax
off of our website. In powermax there is something called a low level format
which will definately wipe off ez bios.
----------
As far as I know, each manufacturer of HD's has programs available to low-level format their HD's, all about the same.
The program writes 0's and 1's to the whole disk, including the Master Boot Record.
The disk becomes "Factory Fresh".
After this, the disk has to be Partitioned (FDisk) and formatted (Fat 32 for example).

by dan.klemann

there are a lot of hard disk utilities which can perform a low level format. BUT it is always done by the manufacture and really isn't needed anymore. If you think a low level is needed try it. But most likely you have a bad disk drive.

by stevepc99

Do not think that just because you can't fdisk your hdd it is bad, this statement couldn't be farther from the truth. If you have loaded a unix partition, then fdisk will no longer work and you will need to perform a low level format. DELPART works really well.

by tshumake

The best disk utility I have found is by Western Digital but distributed by Gateway. It can be found on Gateway restoration CD's and the Gateway web site. It is called "GWSCAN". We use this to write zero's (blank out entire drive) to the hard drive. This utility also does drive scanning to check for errors. It is the first thing that we use to check any possible hard drive problems.

TimS

by anton26

IDE and SCSI harddisks are low-level formatted from the factory.

Some today's motherboards still have HDD Low Level Format in their BIOS Setup utility. You can use this utility to low-level format your harddisk.

You also can get HDD Low-level format utility from harddisk manufacturer such as Seagate (www.seagate.com)

In my experiences, after explaining the user about differences between IDE / SCSI technology and older technology, they asked me to ignore the low-level format.

by it info craver

Low level formatting is a type of hard disk formatting utility that comes with your BIOS. The type of format that you use in your BIOS to format your hard disk is low level. To enter your BIOS, press F2 or Del during boot up.

by hanmer

Instead of using a low level format, use format /u, this is a unconditional format and it also destroys the MBR.

by jconnors

Here is littel Diddy for yea. A company called Micro-Scope came out a with a nice little diagnostic package a few years ago that I still use today. If you can happen to track down this software I can assure that you would not be dissapointed. What you have to know at this point though is..it is " Use at Own Risk " The general Low Level use of the disk is very basic..But if you start messing around in other areas be careful. What you do you to your puter is your
" problem ".If you can't find anything of the sort you can try 'wdclear'it is a program that the College I go to uses for their Boxes.I've not used it myself but others in the school have and have had great success with it.
To top it all off..Good Luck..and make sure that the Low Level is your last option..

by rzan

Although it is not recommended to low level format an IDE drive, there are utilities that can do it. Norton Utilities has a low level format utility called wipeinfo which will write all 0 bits on the drive. SCSI hard drives can be easily low levelformatted through utilities built into the BIOS of the SCSI controller, like Adaptec's AHA controllers by pressing CTRL-A. Anyway, why would anyone need to go to such extremes as low level formatting an IDE drive anyway? If the drive has too many bad sectors and tracks, it is just easier to trash the damned thing and get a new one.

by jdbooe

rzan makes a good point, you must have the bad sector table to re-enter any known bad sectors, and any new bad sectors at the time of low-level formatting. If you are just trying to wipe a disk clean then using the norton formatter, or wipefile utilities. If company security is an issue then replace and save the hard disk, reuse it somewhere inside the company, this is what I do.

by rzan

Although it is not recommended to low level format an IDE drive, there are utilities that can do it. Norton Utilities has a low level format utility called wipeinfo which will write all 0 bits on the drive. SCSI hard drives can be easily low levelformatted through utilities built into the BIOS of the SCSI controller, like Adaptec's AHA controllers by pressing CTRL-A. Anyway, why would anyone need to go to such extremes as low level formatting an IDE drive anyway? If the drive has too many bad sectors and tracks, it is just easier to trash the damned thing and get a new one.

by fred_e944

I bought a Western Digital IDE drive (brand new) that you couldn't even load Windows on, or even format successfully with Format & fdisk. WD tech support advised me to use the Advanced part of Data Lifeguard tools to "write zeros to the drive". Itworked perfectly. The WD tech said sometimes there is garbage left from factory testing, and the way to get rid of it is a low-level format.

by wwodent.ct

mike-low level formatting was an option provided by early releases of award (maybe even ami) bios's. the use of this option on today's ide drives is NOT advised- the format command provided by all dos versions does the same job without drive damage.some older bios releases that do not recognize drives larger than 8(sometimes 4) gb need the hook provided by ontrack disk manager to function properly- do NOT use the format command in these cases.

by derwood

I too am interested in an all-around, non drive-specific utility that will low level format a HDD. This is not for the sake of repair, but for the sake of destroying confidential public records on machines that are being replaced. Has anyone seen such a thing, maybe it runs off a bootable floppy? (best scenario)

Thanks and Cheers, Derek.

by fred_e944

There are a number of freeware file shredders that will properly destroy confidential data. A simple low-level format is insufficient to protect the records. The single "write zeros" leaves residual magnetism on the disk which can be read by a data recovery specialist, though it may involve opening the drive. Removing the residual magnetism takes repeated (12 or more times)writing with different bit patterns to completely destroy the data.

by spydergst1

Hdat is the utlility I prefer. I can't remember who makes it but I sure you can find it on the web.

Format /u is not a LLF.

What is LLF? well as you know HD's are devided into sectors. Each sector has a unique identity and pronounces itself (so to speak).ie IM SECTOR 1, IM SECTOR 2. over time the sectors don't pronunce themselves as well im sector 1, im sector 2. That is why we need to perform a llf sometimes. Once you perform a LLF the sectors pronounce themsevles well again.

It takes longer to do a LLF then a normal format. Once you do a LLF you need to run fdisk a partition the HD. After fdisk you need to performa regular format.

by phascnh

Hi

I use Scorch, Scour and realdeal by Iolo Davidson. It can handle the most extreme needs, up to seven overwrites. It works on the fly also as a last option HD cleaner.
Here is a good starting point for Realdealhttp://www.bonaventura.free-online.co.uk/realdelete

Hope that helps
Phascnh

by jerico5

Derek & co.
I have used low level format utilities by several different hd manufacturers. The best one i have used is by Maxtor. I tried a Seagate LLF on a seagate drive, with no luck, i then used the Maxtor LLF with excellent results. I have also used it on a Quantum & an IBM. Try Maxtors site - you want 'maxllf' It's only about 63kb
good luck

rembrandt

by rjscheetz

I'd be very reluctant to have any user invoke a low level format unless the disk was expendable and non critical. Most users will not have equipment available to allow them to restore a disk in need of this type of repair.

by algae

I have been llf a bunch of old drives gone bad - bad enough i couldnt ghost over them
I was able to find llf programs at each of the drive manufacturers web sites.
I hope that helps - they are also referring to low level formatting as writing 0's

by joe raz

You can low-level a HDD with a Windows 95/98 boot disk...make a boot disk, and add the DOS file DEBUG to it from the WINDOWS directory.
For complete instructions, email me at brunotech@yahoo.com

by bambooza

I agree with Fred in that a low level format will not protect the data from snooping. Even file shredders and erasers cannot guarantee 100% protection and at some point you must ask yourself how would the data cost if it where to leak out. Somewhere along the line it is easier and cheaper to physically destroy the hard drive and buy a replacement. (Five-pound slug hammers work well here)

by derwood

I have to agree with both of you. I have a friend who works in IBM mainframes, and he tells me that they use a mainframe command to write random 1s and 0s across the disk at least a dozen times before being considered clean. He tells me that data recovery specialists are reputed to be able to recover data from at least the last six or seven levels, but at great cost. I agree that at some point, it is better to destroy the platters for the sake of confidentiality. Another good point is that if the information is not sensitive enough to warrant destroying the disk, it is surely not worth the expense of having the information retrieved by a third party. Thanks for the informed opinions!

by onyxruby

Even though a hard drive can be permanently damaged by a spec of dut too small to see with the bare eye, it can't be destroyed with a sledge hammer. While this would certainly make the drive unusable, this would not stop a place like Ontrack from recovering what is on the drive. Also of note is that an electromagnet, even the kinds used to pick up cars in a scrap yard will not erase a hard drive (especially if the cover is on).

Most of what I have heard required overwriting with 12 sets of 0's, 1's, and a combination of the two, followed by other characters depending on the standard.

For permanent destruction of the physical platters you have to heat them (white hot - make sure they warp) with an acetalyne torch, bake them with a blast furnace, or dip them in acid. All of which require specialized equipment and safety measures and should not be done by Joe Public.

The question now is how much is the data worth to you, and how much is it worth to the competition? If you dealwith DOD, than they have their own specs for decommisioned hard drives. Lets say your in Pharmaceuticals, that drive could easily, litterally be worth millions. The majority of the time a drive wipe utility will do just fine, provided the drive to be wiped is /not/ the boot drive.

If it's a very "touchy" situation, you'll have to destroy the sticks of memory too as they can hold residual data.

by wings

Mike,

I found this utility at Maxtor site and the file name is maxllf.exe. You can try to download it.

Cheah

by richard.colond

Look for a file named FDISK.EXE in one of your old MS-DOS system diskettes. Standardly you would use this to low level format your hard disk.

However I believe many of the new hard drives come with different ways of low-level formats. So you might want to check with the manufacturer if it pre-formatted. If it is not then you could use the FDISK utility.

by colcomp

The newer hard drives are formatted at the factory so they can mark the bad sectors and store all this info on the drive. The IDE controller reads this track to get the drive information. A low level format is not usually done by the end user. To do it you might look in BIOS or d/l a utility from the manuf. site

by drvms

Why do U need a low level formatting
Be carefull to do this data or HDD may be danaged
Use Diskmanager
please send why U want to format then I will try to answer U
Ok
Dr Sankaran

by mnewland

Low level format is usually done at the factory and has functions that block out bad sectors on the drive. Western Digital used to discourage a user from doing low level formatting. The other formatting is done from the DOS format command.

by thoma

It is dangeraous because if you format a large HD > 2GB you loose data segments on your HD forever!!! The only way is to get a special tool from your HD producer, s.a. IBM.

by jpropp

necessary, and from what I have read, it could damage or render an IDE drive unusable. A standard FDISK and repartition/reformat should solve whatever problem he's having. If the drive does in fact need a low level format for some reason, I would recommend contacting the manufacturer before doing so.

by ssg0487

Low Level Formating, is the setting of the Cylinders Heads and Tracks, or geometry, of the drive. That is done at the factory if I am not mistaken.

by jon

I use an excellent little proggie from Ontrack called Zero Fill. It zero's the hard drive, taking out all the partitions and any viruses or nasties that might be lurking and you can also use the other progs with it to replace your partitions and fast format them. It fits on a floppy, and from an onsite engineers point of view I wouldn't be without it. Wicked bit of kit!

by gregh

When a low level format is done you re-map the hd. The factory does this to deny access to errors on the drive. By doing a low level format you can expose these errors.

by buffg

Well usually you can find LLF's on the actual HDD manufacturer's website. I have one that is a generic LLF but I don't know where you can find it now except from me. If you want it email me and I'lls end it to you.

by mikeyes

I agree with Bman. Not enough detail....But If a LLF is required, you obviously are trying to overcome some kind of anomaly. Take the time to download the diagnostic tools specific to the drive in question. The manufacturer websites have anything you need and some reasonable documentation or explanation. Try to run the FULL version diagnostic on the drive, (if one is provided) before and/or after, to be sure of the drives integrity

by t. e. walker

Why did the user ask about it? If they are just curious, IMHO you should tell them its a bad idea unless the drive would otherwise be in the trash can. Its possible they aren't clear on what they want/need. Read the other posts for lots of reasons not to do this, and ways to do it if you are truly determined.

by mdg_01

Hi there Mike, yeah low level formatting is serious stuff, in the sense that the procedure really gets down to the media level and scubs ALL traces of data..second only to using one of those magnetic erasers(!) I have a small PC diagnostics utility called 'PC Check' which is freely available on-line which has low level frmt as an option
you could try this..or try C-net download centre for a utility. Cheers

by gardbc

Did you ask the user WHY!? he wanted this formatting option?

If it is because Fdisk won't part/the drive. Maybe he had a Non dos partition on it.

If it is because of bad sectors, a low level format will appear to clear them. Until you run a disk utility that remarks these areas, they are almost always found to still be bad.
Punt, and buy a different drive if they are multiplying to destruction.

Use the drives manufacturer setup disk, like maxblast if you wish to try it anyway. You left out alot of info....that is why your answers are so broad in scope.More info....needed
;

by gardbc

Fdisk /mbr
will rewrite and erase the drive.
To remove an NTFS partition, simply remove "non dos partitions", using fdisk.....

by infra_hdc

IMHO this user have a PC-compatible system, and he want to do format his HDD on the PHYSICAL level.

Several ways to find these utils: 1.See documentation of your system. 2.Find this in software shipping with your system and/or with hardware components. 3.Enter system BIOS setup and find "IDE HDD LOW LEVEL FORMAT" menu or alike. 4.Enter HDD controller BIOS integated utils (by hot-key or by DOS DEBUG utility) and find there. 5.On the HDD manufacturer's web-site. 6.Third-party utils: HDINIT shipped with the CHECKIT, CALIBRATE as part of the NORTON UTILITES and so on.

NOTES: 1.It is too many utils for this, but it is necesary to determinate HDD manufacturer and model of the HDD. Give this information in your request to HDD vendor or manufacturer. 2.Be carefull with these utils i.e. be sure you understand what do you do, otherwise you have a real chance to lose both your data and your HDD physical integrity (with warranty woid); usually this happen after erasing of special SERVO MARKs, which can write _only_ on the factory equipment. 3. It's necesary to back up your information from this HDD before this format.

by fieldse

I have been using a utility called wipe. It can be found on the IBM website. I support users in my company who handle sensitive data. when it is time for them to be upgraded to a newer PC or Laptop, they need assurance that the data on the hardrive will not be recovered.
We run NT4 machines, and this utility has worked wonderfully for me.

This discussion is closed to new replies.