Discussion Locked

Monitor or Operating System

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

The system configuration is
P4
ECS PM800 motherboard
256 DDR
TNT2 Model64 32m Video CARD
Windows XP Home Edition
40g Hard drive

The system was recently built for customer

Delivered the system and hooked it up,upon boot-up the system starts booting,it gets to the XP Home logo screen with the bar running across that denotes operating system is loading,when the system gets to next phase,the screen becomes garbled,it flickers with the colors blinking and no picture.
Was not happening before I delivered to customer,was connected to 15" sony trinitron it worked okay.
Customer has a Samsung SyncMaster 3nE
No electronics close by to cause interference

What could cause this problem?

Here is the kicker,reconnected another hard drive w/Windows Me and the boots all the way to the desk top with no problem.

Thanks for Help In Advance

16 replies

by dmiles

No,I did not consider booting into Safe Mode,and reloading the drivers was not an option since the sytem was booting up and working from the monitor I was using before delivering it

The other part was as I mentioned I can switch hard drives and the system will boot with Windows Me,no problem.

by willcomp

Appears that video settings are out of sync range of monitor. Connect PC to another monitor and set display resolution and refresh rates to conservative values (800 x 600 and 60Hz). Reconnect and adjust settings.

Samsung monitor is 14" with max resolution of 1024 x 768. Frequency at that resolution will probably be 50 to 60Hz. It really needs to be run at 800 x 600 and 60 or 70Hz.

Dalton

by willcomp

An addendum to Chas' response. I doubt that Samsung monitor is plug 'n play. So XP will not be able to automatically adjust settings to allow it to operate properly.

15" Sony monitor will handle 85Hz refresh rate at 1024 x 768. So settings are probably well out of old Samsung monitor's range.

by dmiles

Thanks for taking the time to post an answer,I hae not tried because I will not get the machine back to try solution until next week

by dennis.rhine

It sure sounds like a video driver problem. I would boot it into Safe Mode and install the latest drivers for the video card and the monitor. Also, set the screen resolution down to either 640x480 or 800x600 (I prefer the latter) as there are many 15 " monitors that cannot work well at 1024x768.

by curacao_dejavu

monitor /videocard issue.

we had those Samsungs, and when some new pc's came in they did not work well.
try a lower resolution or change the monitor.

Leopold

by simy

Check the refresh rate set for the monitor. It might be set to a rate that is OK for the Trinitron, but cannot be handled by the Samsung. Boot to safe mode and lower the refresh rate.

by glyall

have you tried remove the video card and reseating it?
Check the video cable for bent pins?
Have you degauss the monitor after moving it?
Check the setting if has a switch for the different type of video cables. Some monitors have a 1/2 switch so that you can connect 2 CPU's to one monitor and switch between two CPUs.

hope this helps
good luck

by thechas

I fought a similar problem when I first started installing XP.

My bench monitor did not support XP's default monitor settings.

I was not able to find a SyncMaster 3nE on Samsung's web site, so I assume this is an older monitor.

XP does not make it easy to change monitor types unless you have a driver disk for the monitor.

What I have been able to do, is temporarily swap in a different video card and for whatever reason, XP then installed a default driver that worked with older monitors.

Or, you could try a different monitor and attempt to force XP to set it up as a standard monitor type.

Chas

by dmiles

I suspect that it is a monitor problem,it will load with ME,but not XP home will apply the answers when I get the system,thanks for providing an answer

This discussion is closed to new replies.