Discussion Locked

Multiple Server Environment

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
We have two Novell servers running on the same network. One server is our email server and the other our file server. Users have been logging in to our email server rather than our file server. They reboot several times and then they authenticateto the file server. I do not want users authenticating to the email server....does anyone have an idea as to why this is happening or how to fix it?

15 replies

by alpha-male

Can you not simply specify the server to authenticate to by selecting it in the advanced properties of the Netware Client? I know this is a simplistic answer, but I would think you could control it that way. We certainly do...

by edb

At your email server console screen type the following command:
set reply to get nearest server=off
this should resolve the problem.
Also check check the propreties in each nwclient make sure to add the server name of the server you wish to authenticate to.

by edb

At your email server console screen type the following command:
set reply to get nearest server=off
this should resolve the problem.
Also check check the propreties in each nwclient make sure to add the server name of the server you wish to authenticate to.

by tohara

I ran into this issue after upgrading to NW5.1 SP4. I found the install added a frame type to the network board. I looked in INETCFG and deleted the erroneous frame type (we are currently using 802.3, it had added 802.2) Once I deleted the extra frame type, my users and jetdirect print servers were able to authenticate to the main file server again.-
Hope this helps!

by jschling

That will only work for IPX environments, the Get nearest server. If you are pure Ip you will have to set up SLP which is covered at Novell TID's. Also, you are better to go with IP than IPX unless you have some reason to stay on IP.

by sanjeevk

There are various options avaialble for this problem. They are listed below. depending on the convinience you can apply any or a combination or all of them. Applying all the options would not harm in any way.

1. Give the server name you need the users to authenticate to in the Network Niehgbourhood > Properties > Client. In this tab, there is a field for Preferred Server. Enter the file server name in this field. The users will authenticate to this server rather than the email server.

2. On your email server give the command to Set Reply To Get Nearest Server=Off (the default value is on). You can put this command in the autoexec.ncf so that in case you switch off the server, the command is set once the server comes back into action.

3. In the NDS database, using the NWAdmin, modify the user properties for Default Server in the Environment Tab of user details to reflect the server you wish the users to authenticate to. This will be permanent (unless you change it again). This will help irrespective of the client settings or the server side set command.

Hope this will help you

Regards
SanjeevK

by sanjeevk

There are various options avaialble for this problem. They are listed below. depending on the convinience you can apply any or a combination or all of them. Applying all the options would not harm in any way.

1. Give the server name you need the users to authenticate to in the Network Niehgbourhood > Properties > Client. In this tab, there is a field for Preferred Server. Enter the file server name in this field. The users will authenticate to this server rather than the email server.

2. On your email server give the command to Set Reply To Get Nearest Server=Off (the default value is on). You can put this command in the autoexec.ncf so that in case you switch off the server, the command is set once the server comes back into action.

3. In the NDS database, using the NWAdmin, modify the user properties for Default Server in the Environment Tab of user details to reflect the server you wish the users to authenticate to. This will be permanent (unless you change it again). This will help irrespective of the client settings or the server side set command.

Hope this will help you

Regards
SanjeevK

This discussion is closed to new replies.