12 replies
by trueevee Accepted solution
by older mycroft Accepted solution
The socket that has the prong in the middle, is a complete unit that is soldered directly into the edge of the motherboard. Due to the strain placed on the socket each time the jack is inserted/removed, the prong is capable of breaking off occasionally, but once it's broken off you can't just 'put' it back on.
At the very least you need to replace the entire socket assembly. This will involve de-soldering the existing broken socket to remove it from the motherboard. Then you need to procure a replacement intact socket, then solder it back onto the motherboard as the replacement.
Unfortunately, you need to have expertise to solder anything onto a motherboard and be equipped with strictly temperature-controlled soldering gear. Any slip-ups at this stage would render the motherboard unusable forever, by damaging one or more of the data tracks running from (or close to) the AC socket.
Also disassembly of a laptop is not something to be undertaken lightly - there are lots and lots and lots of extremely tiny screws, and to replace the AC socket would require complete disassembly of the laptop in order to remove the motherboard prior to the de-soldering/soldering process.
This particular example of laptop damage (usually caused by the socket suffering some form of trauma while the jack is in place) is so labour intensive that, if the laptop was still under warranty, I'll guarantee the repair company would just replace the entire motherboard because it is easier and quicker than repairing the socket alone.
You really need the services of a computer technician. :(
by oh smeg Accepted solution
Toshiba [b]Do Not[/b] have Service Manuals available and these are complicated Static Sensitive Devices.
Just removing a cover under the wrong conditions can cause the destruction of Electronic Compo nets. Using the Wrong type of Electric Soldering Iron will destroy the M'Board Components. Using the wrong type of Soldering Iron may lead to the destruction of the Computer completely.
I have seen one person use a Gas Fired Soldering Iron suitable for a Plumbers use to attempt to Solder in a Transistor and they set the Circuit Board on Fire which isn't supposed to happen but if you expose anything to a hot enough Flame it's going to burn.
If you don't already have th correct tools to work on this you will find that they are going to cost you far more than to have it Professionally Repaired and Even if you are willing to buy the correct Tools there is no guarantee that they will be of any use to you as when you get it apart you may very well find that the Circuit Board has a piece broken out of it and needs replacing. Under Ideal circumstances the best to hope for is that you need to replace the Jack on the M'Board but as Toshiba Use strange nonstandard Jacks you may very well find that it is possible to remove the Jack but not buy a New One to fit to the M'Board.
You need to remember that it's not just the size & Shape of where you plug the connector in but how it is soldered to the M'Board. If you do not have the correct socket there is no way to solder it to the Circuit Board safely that will not allow a Short Circuit to accrue and possibly allow the unit to catch fire.
Col
by older mycroft Accepted solution
by rob miners Accepted solution
by oh smeg Accepted solution
They rang up with a Failed Circuit Board that required 1 PNP Transistor to be replaced. On those Circuit Boards this was a common failure and it was wanted fixed yesterday. I did suggest sending it to Brisbane and I would return it the same day repaired but that wasn't fast enough so I weakened and told them the type of Tranny to buy and to just remove it with a Soldering Iron.
I still do not fully believe that it wasn't deliberate and they they where having a go at me but I must admit that always sent down failed Circuit Boards for repairs after that. :D
Col
by older mycroft Accepted solution
He CLEANED all his circuit boards by drenching them with WD-40 then posted to ask why they didn't work anymore!! :^0
THAT was one of my funniest moments on TR to date. :^0 :^0 :^0
We really should construct a TR Hall of Fame !
by nk303 Accepted solution
by older mycroft Accepted solution
Not exactly hot on detail are you ?!!
...Now I wonder why ? ;)
by oh smeg Accepted solution
But I like the one with the Keyboard not working and after much mucking around it turns out that a Liquid has been split on the Keyboard and they keyboard torn apart and then attacked with a Rag to generate Static and that wasn't important.
At least the WD40 would have washed away any contaminates but I think water is better. :p
Col
by older mycroft Accepted solution
Ragtime Dance, but couldn't find one! ;)
Fair go though - as the bloke insisted, it WAS utterly unimportant !! :^0
by 1bn0 Accepted solution
The part.
http://www.laptopjacks.com/view_part/Toshiba-Satellite-U205-S5034-Laptop-DC-Power-Jack-TS472730.html
Sample disassembly's'.
http://www.daniweb.com/forums/thread34183.html
Soldering instructions READ THE WARNINGS!
http://www.talkingelectronics.com/projects/Soldering/Page1.html
NOW DISREGARD EVERYTHING AND TAKE IT TO SOMEONE WITH EXPERIENCE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending