Question Locked

MY XP PC won't start the boot-up sequence all the time.

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
It jsut gets to the Intel inside screen and sits there. I fixed it once with a new DL 2032 battery. It's a 4+ year old PC and that worked for a couple of weeks and now it's doing it again. I have used CC Cleaner to keep it cleaned and the registry updated. The last few days it has finally booed up after 15-20 minutes. This morning nothing. I have backed all the data up. I just want to know whether the HD or MB is fried or at least sick. Any ideas?

9 replies

by tintoman

replacing the battery again you should do so. If that doesn't work you could try to clear the cmos, there might be a jumper on the motherboard labelled CLR_CMOS or BIOS_RST something like that, failing that you could be looking at a failed bios chip but before you do any of this you should make sure you disconnect all peripheral equipment other than keyboard and mouse, ESPECIALLY USB devices as these can sometimes prevent booting

by darmstadtrunner

I tried this and it worked on the second try. I had to set the jumper on pin #3 which really does nothing and it booted up and worked fine on the second try. Setting the jumpers on CMOS - normal didn't allow a full boot-up. I took the printer and external HD USB connections off the first time, but put them back the secondd time and it worked. I'm still amazed at what can happen to a PC and what great people are out there to help. Thanks everyone for the suggestions. I'm saving them for future reference.

by older mycroft

All external USB HDs should be treated in exactly the same way as you would treat (or at least SHOULD treat) a USB Thumb Drive.

Just as you should use the Safely Remove method when disconnecting a thumb drive, you should employ exactly the same practices with a USB HD. If you don't, one of these days the USB HD will be dead or at the very least its partition tables will have been corrupted. Your stored data could then very well be lost forever.

USB HDs are not designed to be connected all the time and are certainly not designed to be attached at boot or at shutdown.

You should always Safely Remove them prior to shutdown and only attach them after booting up.

by older mycroft

Download [b]UBCD[/b] - Ultimate Boot CD - and burn the ISO image to a CD.

You then boot from the UBCD, which has its own self contained operating system (so it bypasses Windows and whatever is on your hard drive).

Once the UBCD is running you can utilise the diagnostics software it contains to check out your hard drive(s) and RAM and other ancillary hardware.

http://www.ultimatebootcd.com/download.html

by ---tk---

What kind of PC do you have? So, is the boot sequence is not following the right order? Or is the PC not even getting to the boot sequence?

by snuffy09

do you have any external devices hooked up to it? Like USB Hard drives or Printers. if an external HD is failing this could cause a stalled boot problem.

Your Power supply may also be failing.

I think if your Motherboard was dead or dying you would not see the intel splashscreen, but if it was working properly it should at least POST.

to see if it is the HD try unplugging the power from your internal HD and then power on the PC. if the mobo posts then it may be the HD is failing.

by darmstadtrunner

Clearing the bios seemed to work. I just connected the two jumpers that said it would clear the bios and tried to turn it on. Nothing happened and when I reset jumpers to normal, it did not boot. But I tried it twice and it started booting up fine. I took the external HD out of the loop and will take the printer out of the loop the next time I try it. It would not boot up last night after a normal shutdown until I cleared the bios a couple of times and this morning again. It has been on a working since 0800 hrs and just "crashed" at 1530 hours. There was a blue screen with white letters saying there was a problem and it dumping physaical memory. Now it won't boot again. Did I clear the cmos correctly and is there anything I need to do to the cmos or registry if it comes back again? I still get the spin up of HD and the Intel inside logo before is just goes into "idle" mode.

This discussion is closed to new replies.