Discussion Locked

NAT in the Classroom

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,
I hope you can help me with some suggestions. I'm teaching a class in 70-216 and although the concepts of NAT are clear to me, I have never set this up. I haven't tried it yet and I'm two weeks ahead of schedule.

Does anyone have any suggestions or experience with this?

Appreciate your help.

9 replies

by leo.valmores

NAT inplementation can be done in two ways: one is to setup a PC with two NIC cards. NIC1 card should be connected to the external INTERNET/WAN wherein you configure the IP address of your ISP, their primary and secondary DNS address. NIC2 is for your internal network and you can assign 10.x.x.x or 198.x.x.x domain addresses. MS OS that support Internet Network Sharing with NAT are WIN98 and WIN2000. For WIN2000, internal network address is set to 198 domain.

NAT inplementation can also be found in those Cable or DSL modem/Routers boxes. Manuals from the manufacturers will show you how to configure the settings, normally through Web-browser.

In either case, it is clear at the onset that you must prepare your addresses handy both for internal and external networks.

Hope this helps!

by mckaytech

What do you have to work with in the way of classroom/lab equipment?

Although you're teaching a Windows class, I use a pair of 486 workstations running LRP (Linux Router Project) software to teach the concepts of NAT because I don't have the funding for equipment that is Windows2000 capable. You can also add a package called tcpdump that will capture and display the packets as they whiz by and it still all fits on a floppy disk.

At the end, I then use a Microsoft Webcast for showing the setup on an actual Windows2000 server.

One minor note - in an answer above, the private networks were identified as 10.x.x.x and 198.x.x.x . The Class C private network is actually 192.168.x.x, I believe.

paul

by ins413

I too am an instructor and just finished teaching NAT. I currently am teaching 70-221. My students are expected to know how to set up NAT at this point, but I had to go over some high points this afternoon, just to get them going. NAT should be setup using two NIC's. One private and one public. NAT in W2K has alot of very useful capabilities. Some of which are Dynamic Allocation of IP's, DNS name resolution, and some very limited security. It should serve as a DHCP server for you internalnetwork and can use APIPA (any private IP should suffice). One bad thing about doing this is that NAT wants to be the only server providing these services. To get NAT installed go to Start--Programs--AdminTools--and select Routing and remote access. RRAS MMC will appear. Click on the plus sign (+) beside the IP routing node and right click the general node. Select NAT. Once it has been installed, you can right click and go to properties from the NAT node and set all configuration up from there. This should get you on the right track. If you require any other info feel free to email me. Good Luck.

by highorbit

Don't quote me on this but...!

NAT is the process of passing information between 2 IP ranges, generally a private range (LAN) and a public range (Internet).

A router will traditionally take the IP packets and make it look as though they have originated from the router itself, essentially acting as a relay.

As far as I know anything with a publically available IP does not need to perform NAT, as an example a web server with two network cards (one internal and one external) does not use NAT at all, although the router does still route it's IP packets. After all, if it has a publically acceptable (and therefore unique) IP why would it need to? Could be wrong on that though!

If you wanted to avoid the dual network card a NAT pool would be set-up on the router, this defines where the packets for a particular public IP should be sent, this would be Network Address Translation.

Finally a note on the private ranges (class E I believe):

10.0.0.0 to 10.255.255.255
172.16.0.0 to 172.31.255.255
192.168.0.0 to 192.168.255.255

I think those are right. The 10 range used to belong to IBM. The 192.168 range to microsoft...

This discussion is closed to new replies.