Question Locked

no keyboard, mouse, monitor, upon reboot, until 30 min. later

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My son, with the help of a friend, just built his 1st computer.
I wasn't there, so am not sure what they did. As he describes it, I'm at a bit of a loss as to what might be causes of the problem.

This is a high-end, gaming system, AMD processor, SLI nvidia card, 750 wt psu, SATA HDD, not sure what all else. It's not connected to the internet.

When they started it, it ran fine: he said they got XP on then the motherboard (DFI) drivers. All seemed okay.

Upon reboot, there was nothing. No keyboard, mouse, monitor and he thought, no HDD as well.

However, 30 minutes later, everything is fine.

I thought at 1st a PSU problem--something overheating after system fans go off and that was killing things. But he says when he tries the restart, the case fans come on. So the PSU is at least working part way.

I thought okay, probably a video driver. He says the video card works okay in another system. Which still doesn't mean the driver on "his" system is okay. He tried another video card in his system and the same thing. --no reboot, until 30 minutes has gone by.

Then I thought, could be a BIOS problem and the system is hibernating?

Still suspect though, the video driver. but with it working fine, then failing, and no keyboard to get into safe mode or even BIOS, where do we go from here?

I realize this isn't much info to go on, I'll give more as i get it. Maybe you have some ideas where to start?
He said he ordered a new mobo, but has to send this one back 1st, which he doesn't want to do if that's not the problem.

Ideas anyone?

Thanks...

6 replies

by Former member

It sounds to me like the motherboard is earthing on the inside of the case. When you get a motherboard you sometimes get a few small red (or cream)disks that sit under the motherboard to keep it away from side of the case, if these have not been put on properly then this will be the reason for your computer to suddenly go off or not boot up. If it is not fixed then the psu would soon go to.

Please post back if you have anymore problems or questions.

by stars1234

Thanks Peconet.

My son says, they screwed the brass standoffs into the case, set the mobo on top of them, then placed the small non-conductive washers on top of the motherboard screw holes that match the standoffs and put in the screws. He didn't see any thing else.

Or are these what you are talking about & they should have been put between the standoffs and underside of the mobo?

He didn't mention any discs to keep the mobo from grounding on the side of the case.

Just before I read your answer, I had almost decided to give him one of my PSU to try, but on 2d thought, told him if he's blown the mobo, then it'll blow the PSU, just as you said.

I gave him a DOS boot disc, to see if it that works. And told him to reset the BIOS.

He said the instructions say to reset CMOS, from software. I told him, CMOS is not BIOS and there will be a jumper on the board. But not knowing DFI mobos, maybe they call CMOS & BIOS the same?

I asked if he heard a beep when he tried starting, after shut down. He said no. But then told me they didn't connect the speaker.

I asked if they were grounded before installing. He said yes.
Asked if they used any pressure to put in the CPU or HS/FAN, he says no.

It sounds to me more and more like the mobo grounded & probably blew the PSU? Or the PSU grounded someplace (maybe they didn't put the 4 pin plugs in right?) and blew the mobo or PSU.

Any way to test? Or does he need to put the washers on the underside of the mobo?

by oh smeg

Yes these are them they need to go between the M'Board and the Brass Standoffs.

But as a fault finding option pull the M'Board out of the case sit it on some clean blank White Paper and connect everything back up and see if the problem persists.

If it does it's not an earthing issue and you really need to find out the full specs of the Hardware involved to post back with so we have a fighting chance of helping you out.

Col

by stars1234

Thanks, sorry to have taken so long to get back. --was on the phone with my son.

I agree, the easiest way to test whether the mobo is grounding is to take it out of the case. Trying to talk my son into doing that is a bit harder. I tried to explain to him how to do it, but he wants to test the PSU instead.

Unfortunately for him (fortunately for me), my extra PSU is ATX and he needs a PCI PSU. So he can't fry mine. But he wants to use my digital multimeter to read the rail voltages--I guess I can let him do that (and short out the PSU when he's testing).

I realize you can't help much, with the little information we have. I appreciate what has been said.

Please help me understand how the washers and the standoffs are to be used to keep the mobo from grounding to the chassis.

The underside of the mobo that sits on the standoffs is just plain pc board, with no solder/conductive material, there.

It seems that if the washers are put between the standoff and bottom of the mobo, they would do nothing, since there is no metal there anyway.

However, on top of the mobo, there is solder around the screw holes.

I would think that's where the washer should be, to keep the screw from coming into contact with the solder. Is this wrong?

Tomorrow, my son is going to get my multimeter and test the PSU. --but I'm going to bet it's the mobo, and it may have already damaged the PSU as well.

Or perhaps there's a setting in the BIOS that's causing the computer to go to sleep for 1/2 hour before it can be rebooted?

He does get a beep, when he turns the system on, but nothing else is getting power., except for the power standby and RAM LEDs.

I'll know more tomorrow.

If you can help me understand how putting the non-conductive washer between the non-conductive part of the mobo and conductive standoff, keeps the mobo from going to ground, I'd appreciate that.

by oh smeg

But I only use good cases so I don't have an Issue.

The main reason why you need to isolate the Back of the M'Board from the Standoffs isn't so much the standoff shorting out on the M'Board mounting Holes but on some other thing sticking through the M'Board or a track if the protective covering gets scraped away. By giving them that bit of clearance it prevents the worst of the issues that can occur and stops things actually contacting the Power bits.

The front of the M'Board which has the soldered surfaces are there to either Earth or Ground the M'Board or to provide a bit of extra strength to the Fiberglass construction of the Circuit Boards used to make the M'Board. A good Ground Plane is not necessarily a bad thing.

What I find confusing here is the time that the peripherals remain dead/unresponsive as that is strange It could be something overheating like the North/South Bridge and in a case these can be hidden or obscured so that are hard to get to. Also if these have Fans on them are they working or has something in the case be forced against them stopping the fan from spinning?

The last Multimeter that I had someone else [b]"Borrow"[/b] was plugged into the Mains Socket on a low resistance range and then power applied. Pity it was only a couple of hours old at the time and I had to fight like hell to get the Boss to buy it. But I'm told that he was really impressed when it blew and he never came down to play with my tools again so it wasn't all bad I suppose. :D

Has anyone actually unplugged the Mains Power and see if it works after the thing is plugged back in? That might be worth a try if it hasn't already been done.

Col

This discussion is closed to new replies.