Discussion Locked

No sound!!! Integrated sound on motherboard

0 helpful
22 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I just built a computer and fired it up. Everything works but the sound. The operating system is Windows 2000. I tried it with Windows 98 as well to no avail. I've updated the Bios,CMOS, Chipset, Motherboard drivers...everything I could think of. Still now sound. I notice there is a conflict in device manager on "unknown device" under "sound, video and game controllers". I have tried to remove all devices from there and restart the computer. Nothing. I disabled the onboard sound in CMOS and installed a new PCI sound card (Mad Dog) and still no sound. Under sounds and multimedia properties, Sound volume controller is ghost out. Under Audio tab, it says No Playback Devices. My mobo is shuttle AB60N v1.2. Please help. Thanks in advance.

22 replies

by sgt_shultz

could this be it?
from support.microsoft.com kb article 227805
Speakers Do Not Work Correctly After Upgrading to Windows 2000
SYMPTOMS
When you upgrade your computer from Microsoft Windows 98 to Windows 2000, your speakers may not work correctly.
CAUSE
This issue can occur if you use a speaker selection other than Desktop Stereo Speakers in the "Sounds and Multimedia" tool.

Windows 2000 Setup configures the "Sounds and Multimedia" tool to use Desktop Stereo Speakers, which is the default speaker selection.
RESOLUTION
To resolve this issue, manually configure the speaker configuration in the "Sounds and Multimedia" tool:
Click Start, point to Settings, and then click Control Panel.
Double-click Sounds and Multimedia.
On the Audio tab, click Advanced under Sound Playback.
In the Speaker Setup box, click the speakers you want to use, and then click OK.
Click OK, and then close Control Panel.

by sgt_shultz

also check out whether sound driver is set to digital speakers. maybe you have analog speakers? did you try for sound via headphones?

by fathom

There wasn't any sound with Windows 98 neither. I did not have the option to click Advanced under Sound Playback because it is ghost out.

by cg it

humm unknown device in device manager means drivers haven't been loaded up. Now sometimes W2K acts pigheaded [usually associated with unsigned drivers] and won't install the correct drivers. I have this happen on DLink NIC cards. So I have to manually browse the CD navigate to the drivers folder, pick the W2K/XP driver folder, open that up and choose the driver. Then the bloody thing will work. Might try that with your sound card drivers be it the onboard peripheral or the PCI card.

by fathom

I manually browsed the CD to the drivers folder and picked the appropriate OS Win2k. Nothing...still has a conflict, still no sound.

by parvus1202

Alright, another suggestion, do you know your motherboard model? Go to the site and download drivers for your motherboard. If you don't know, you can open your case and look inside. Write it down and search the maker. There is always driver available. It includes sound, modem, usb etc.

by fathom

I already downloaded and installed the latest and greatest drivers for the motherboard. It didn't seem to change anything.

by cg it

hummm sounds like a no suggestions will work case.

PnP, though not well though of, usually does a good job in installing and configuring devices and assigning IRQs. I consider IRQ conflicts in W2K/XP systems rare and usually pop up when a user mucks around with device IRQ assignments.

Maybe TheChas might help ya out.

Good Luck

by cg it

one other though is that you've got 2 active sound devices. The onboard sound card AND the PCI card. If both are installed, then PnP will run on the mumbo and you'll have a conflict.

by fathom

The PC had no sound when I was using only the Mobo integrated sound device. When I tried the PCI card, I disabled the integrated sound device the way the manufacturer of the motherboard instructed; by doing it in CMOS. That's the only instructions I was given by "Shuttle".

by cg it

If the onboard sound card doesn't work, a PCI add in sound card doesn't work, no matter what you do or what driver you install, or computer configurations you try chances are your not gonna have sound.

Buy a new board.

by thechas

It sounds like you have a partial load of a bad driver.

Remove ALL multi-media devices from Device Manager.

CAUTION, the next step involves editing the registry.
It is "best" practice to back up the registry before proceeding.

Run regedit.
Browse to the hardware enum key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum

Examine the individual keys, and delete those that relate to the sound devices.

Search the registry for "key" terms found in the sound device keys. Delete keys as appropriate.

Shut down the PC.

Install or enable the sound device of choice.

When you boot up, click cancel when Windows attempts to install the sound device.

Run the setup software for the sound device.

On occasion, I have had to wipe the hard drive and start over to recover from a bad driver installation.

Chas

by rcom

After you install windows you need to run the installation of drivers from the CD provided with the motherboard. Don't worry about what's in device manager until after you've ran the CD. When you run the CD it expands the drivers then the devices will be found and correctly installed. So without running the software the drivers will not be found when windows searches for them. Take out any extra cards until you get all on the motherboard working first.

Run the CDROM if it doesn't autostart open My computer or explorer and reun it from there. Select utilities from the menu and install the drivers in the order listed.

1. Intel Chipset Driver
2. Intel USB 2.0 Driver
3. Realtek Audio Driver
4. Realtek LAN Driver

by etoile

You have probably tried the really obvious - are the speakers or speaker cable faulty? You didn't mention that you had checked ...

by fathom

It has nothing to do with the speakers. I can't even add the tray Icon for sound. It's ghost out in "Sounds and Multimedia Properties". I'm sure it has something to do with the "unknown device" under "sound, video and game controllers". I try to manually install drivers for it from the audio driver directory to no avail. The upgrade device driver wizard is searching for "Microsoft Kernel System Renderer" when I do this. Microsoft has no solution for this. I have run into this problem a couple times before on other systems and never could fix it.

by rcom

OK, let's do this.

You may have done some or all of these steps but maybe not in the correct sequence or something so please read the whole process.

Remove or disable the sound card and modem. Check to see if there's a windows uninstaller in add remove programs. If so uninstall the software for it.

After rebooting make sure the devices are gone. If not there may be a jumper on the mother board to disable the features. After that remove all the multimedia functions using add remove programs, windows setup.

Boot to safe mode and again delete all the sound entries in device manager. Some of the things that you've uninstalled may still be there. Now you shouldn't have anything to do with sound installed on the system at all. When you reboot the sound section in device manager should be gone.

Now go back and re-enable the onboard sound (only). When windows starts and finds the sound card it shouldn't automatically find the driver unless it's included with windows. When it asks you for a path point to the wrong place so that it comes up as an unrecognized sound device. Now you should have unknown sound in device manager. Run the sound install from the motherboard CD. Once this completes go to the next step. Which is updating the system. Especially Direct X. If alls good move on to the modem.

If there's still issues get a bit tougher. Disable com ports, USB and NIC.

This discussion is closed to new replies.