Discussion Locked

Novell 4.x and ArcServe 6.10

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Our vendor recently applied Service Pack 7 to our Novell 4.x server. I am running ArcServe 6.10 backup software with Service Pack 2. My backups are now taking 20 - 24 hours. They used to take 4 hours. I have had the SP7 backed off, deleted and reinstalled ArcServe, nothing seems to work. Does anybody have any suggestions. I tried something different every night but have nothing fixes it. HELP!

17 replies

by ttate

Are you SURE sp7 was backed out fully? Sometimes the SERVER.EXE file is patched and you have to manually rename the SERVER.OLD file to SERVER.EXE. Do you have other servers that have not been patched to sp7? Can you compare files in the SYS:SYSTEM and C:\NWSERVER directories between the two servers? More than likely there is a "patched" file still sitting out there and getting loaded.

Are your tapes good? Has your backup cable come loose? Does ArcServe give any error messages?

Good luck!

by mkelley

You might try doing some purging on your arcserve database, also, make sure you reset the archive bit on your backup jobs.

by gregc

I would also check the C: drive for and .old copy of server.exe and rename that file back to server.exe . Here is another thought, get the latests drivers for your LAN cards and your SCSI card and and other drivers and apply them. Also look at Novell's TID# 2937318 and see if it can help you out. Is this server in a tree by itself? Or is it part of a tree? If it is part of a tree you should upgrade the DS on all your servers, starting with the root. Hope this helps.

Greg

by shanghai sam

Try setting the Arcserve Backup "Options/File Options" to Deny None/No Retries, you may be retrying unavailable files (user held, or Novell attribute damaged) - the Arcserve default is 5 retries, and your increase in backup time reflects some bakcups that I've fixed that way.... It is important to check through the Backup Logs to determine which files and directory areas are irritating the backup - you typically must copy them out to another server or directory, delete the original files anddirectories, then copy them all back and reapply the permissions. With all that done a DSRepair and Vrepair is in order!

by mikewaldrop

Do you have all of the Arcserve patches? Arcserve recently released a patch for 6.1 that signifigantly improved performance. I would download all of the arcserve patches and install them on your backup server and try it again. If the performance is better re-install SP7 and see what happens.

by zoel

Please provide more detail on your hardware setup and backup methods. I need to know what kind of server, ram, hard drive space being backed up, tape drive type, controller type, if your sharing one controller for the tape and hard drives, wheter this server is being backed up remotely, or is backing up remote, servers of clients etc. Also, make sure you get sp7A, not sp7. sp7 had an issue with Tsands.nlm that will cause abends when opening and closing NDS for backup!

Under backup options in arcserve on the console you may want to turn off backing up files over 2gb if you know you dont have any that large. I have a problem where occasionally a file becomes corrupt, and the size is misreported. Arcserve will spend hours trying to packthe file down (using the misreported size) to back it up.

On you SCSI card settings make sure you have sync negotiation turned OFF and disconnect turned ON for both the tape drive and the controller. Also slow the speed for the TBU down to its lowest setting (as most

by kathy.maciejeski

One problem you should be aware of is an incompatibility with ArcServe 6.1. The TSA410.NLM, SMDR.NLM, and TSANDS.NLM files that come with Support Pack 7 can cause your server to abend with ArcServe 6.1 when it backs up NDS. If you use ArcServe 6.1, you must copy back the versions of TSA410.NLM, SMDR.NLM, and TSANDS.NLM that came with Support Pack 6a to your SYS:\SYSTEM directory.

by berryhill5231

Verify what you are backing up. You may be backing up things that you do not need to. I recently encountered a client that was backing up 13,000 clipart files. Rediculous!
There is a limitation on directories with more than 2000 files. The buffers and swap space fills up and at that point files are being swapped out one at a time. That wil be slower than frozen molasses goin' up hill.
I have solved more problems than you can imagine by being able to turn off compression.

Apply the latest Arcserve Service packs and the new nlms. Do it exactly as the instructions specify and it should work. I have never had to apply any Novell patches for this problem, With 4.xx or 5.xx. But that only says that I had not encountered a Novell backup issue. The main thing is to verify your backup. If you don't need compression don't use it.

Hope this helps,

Mike Berryhill

This discussion is closed to new replies.