Discussion Locked

NT 4.0 with 20 Gig Drive

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Ok here goes 1000 points for the correct answer.

I am going to try and upgrade my NTSERVER's my new configuration I want to use is:
20 gig HDD
800 mhz Intel Pentium 3 Processors
256 megs ram
Intel motherboards

Right now I am booting NT from the cd and installing. It gets all the way through the install process. (boot partition is only 4gigs) But on the first reboot (which I cannot stop) when it comes back up it runs into the blue screen of death and stops.

I have called Microsoft and even paid thier $245.00 fee to be told to upgrade to windows 2000. This is not an option. My company made a 20k investment 3 years ago in Windows NT (before I came here or else we would be *nix based) so they are unwilling to spend another 20k only 3 years later for the upgrade to Windows 2000.

Someone out there must have done this in the past and for 1000 points if they documented it (or is willing to document it) I hope they can share with some of us who need to upgrade the hardware. :-)

BTW Microsoft told me it can be done, they have also told me they refuse to document it as they are trying to sell Windows 2000. I know it has to do with installing the service packs but I cannot even get to the point of installing the service packs before the server crashes.

21 replies

by dbrown

This happened to me several times in the past and it always had something to do with the hard disk controller. The first time the system boots off of the CD and you see the first blue screen you have a few seconds to hit the F6 key. In this screenyou will be able to manually configure your controllers.

Good Luck!

by technojunkie

The previous answer about F6 for additional storage devices is probably the first place I'd go; the second would be an image utility. Allow me to explain: Symantec makes a product called GHOST (and yeah, I guess I'm endorsing it - I love it!!). In the past, we've run into a similar issue with new workstations (not servers). We set up the entire system on that 4 gig (max) partition, make an image file on another server, repartition your drive to one partition, and lay the image back onto the 20 gig partition. You'll inevitably get an error from ghost that says that NT won't boot with anything larger than a 4 gig partition, but it does anyway. When the system boots, you'll have a 20 gig system partition. *NIX guys will know how to make an image without a third-party util.

by mjervis

Sure I can make an image and then deal with all the errors from installing it with a new mother board and resources. I am trying to not do this.

by russ werner

I have a server setup using a Dell 700mhz with 2-20 gig hard drives and 256 megs or ram, but I dual boot!
Win NT4.0 Workstation was installed first on a 3-gig Fat partition. The remainder of the 20 gig hard drive was formatted NTFS as D-Drive andNT Server was installed on D-Drive. The second NTFS drive is for data. I boot on D-Drive and run NS Server with no problems. I didn't do this specifically to work around your problem, it was a choice made at the time, but I never got your problem indoing it this way. If you have a copy of NT Workstation, it is simple enough to give it a try. Surely cheaper than moving to Win 2000!!!
Good Luck.

by mjervis

for security reasons I don't need extra OS's on the server on other partitions. I know there is a way to do this ... I just haven't found it yet.

by cavedweller

I just had this problem myself (with a 40G drive). NT doesn't support disks this large until SP-3. Your install CD is probably no later than SP-1.

1. Does your BIOS support drives >8G ? It probably does since you mentioned P3's. This is usually a concern with older BIOS. Update the BIOS if necessary.

2. Boot from CD and configure your disk so it only has the 4G boot partition. Delete the others. Install NT.

3. Install your current SP (5 or 6a).

4. Use Disk Manager to setup the rest of the disk.

This worked for me. Good Luck!

by mjervis

Thats exactly what I'm doing however when it reboots after the install before it allows me to do anything is where my problem lays. I cannot get to the point of installing the service pack. If I could install the service pack then my problem would go away.

by bmiles

I have a couple of questions. Have you tried using another smaller drive with this motherboard? My point here is that the problem could in the motherboard. The BIOS could be the culprit. Have you checked the web site for the motherboard manufacturer? This might not be a Microsoft problem.

by mjervis

Intel Motherboard and it is on the compatibility list. There is no updates from Intel for this board and the place of puchase said and showed me they are using the same boards with NT 4.0 for thier own use.

by jcurl

You need to get an updated atapi.sys file (post SP4) to use during install of NT. See Q197667 for instructions on how to get the updated file, and how to get the install process to use it instead of the old version.

Good luck,
Jeremy P, MCSE

by tbradley

If your system has an AGP video card, get
rid of it, and put in a generic 4mb PCI card.

There's some undocumented problems with NT and AGP, and I've successfully gotten around a problem similar to yours 3 times in the last 2 weeks, upgrading Netfinity servers from Novell 3.12 to NT4.0.

by mjervis

No AGP Card but thanks for the info it could help others. I understand that AGP came out after NT 4.0 and NT has no support for it. :-)

by edward clint

First, could you give more detail on the blue screen error? like it says STOP .. then?

That could help quite a bit..

Is this scsi or ide?

Have you removed all non-essential hardware(sound cards, modems, extraneous video cards, all network cards, etc..)? I mean not essential to the install of NT. One of those drivers could be causing problems.

Have you checked all hardware against the MS hardware compatibility list? http://www.microsoft.com/hcl/default.asp

What is your goal exactly? just go get NT working on this new hardware? a 4gb sys partition is ok, so long as you can access the other 16 gigs as a separate partition right?

-EC

by mjervis

All non essential at boot up cards have been removed.

Yes I have checked the compatibility list.

My goal is to replace a server that has been in use for 3 years.

by bohicam1

My only suggestion would be to make the boot partition smaller. Our servers have 500MB boot partitions as you are not supposed to have anything else on that partition with it. Go into disk administrator later and configure the rest of the free space.

This discussion is closed to new replies.