Discussion Locked

ntfs.sys corrupted

0 helpful
25 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a computer that has Windows XP Professional installed with SP2. It was running perfectly until just a few days ago. The owner of the computer told me that it just suddenly flashed a blue screen (BSoD) then rebooted, and continues to flash a BSoD and reboot. It does this even when attempting to go into safe mode. Booting using the option to use Last known good configuration doesn't cure it either. The BSoD error message includes NTFS.sys corrupted. How can this happen and how can it be cured? I have tried 5 different hard drives in that computer in an attempt to install Windows again, but it won't take any O/S other than Win98 so far. Same error message, ntfs.sys. Even after a low level format.

25 replies

by blackcurrant

Hi

Have you checked the drive with any diagnostic tools? Also, have you checked the drive for viruses?

You say you have tried 5 different drives in this machine and they are all giving the same error?

Have you tried this:
http://support.microsoft.com/default.aspx?scid=kb;en-us;822800

this is the same problem caused by bad memory - very similar symptons:
http://www.ntcompatible.com/thread24396-1.html

and have you seen this also:
https://www.techrepublic.com.com/5100-22_11-5234679.html?tag=search

Good luck

by daz'n'ash

Well, I tried all that, it didn't cure what ails it. Thanks very much for your time though. Please add any other suggestions you might have.

by jaqui

create dos boot floppy,
copy ntfs.sys from a system with hexp pro sp2 to the floppy ( or another one )
boot the bsod computer with boot floppy.
copy the ntfs.sys to the windows system(32) [ or wherever it was ]

pull floppy.
reboot system

by dmiles

You cannot access a NTFS file system with Windows 98 boot disk

To resolve this problem, replace the missing or corrupted Ntfs.sys file:1. Use the Windows XP startup disks or the Windows XP CD to restart your computer.
2. When the "Welcome to Setup" screen appears, press R to select the To repair a Windows XP installation using Recovery Console, press R option.
3. Type the number of the Windows installation that you want to access from the Recovery Console, and then press ENTER.
4. Type the administrator password when you are prompted, and then press ENTER. If no administrator password exists, just press ENTER.
5. At the command prompt, type the following commands (press ENTER after each command):
cd \windows\system32\drivers

ren ntfs.sys ntfs.old
Note This step renames the corrupted Ntfs.sys file to Ntfs.old. If the Ntfs.sys file is not found, the file is missing.
6. At the command prompt, type the following command, and then press ENTER:
copy cd:\i386\ntfs.sys drive:\windows\system32\drivers
Where cd is the drive letter for the CD-ROM drive that contains the Windows XP CD, and drive is the drive where you installed Windows XP.
7. Remove the Windows XP CD from your CD-ROM drive, type quit at a command prompt, and then press ENTER to quit the Recovery Console.
8. Restart the computer.

by willcomp

OZiT,

Some suggestions. Appears to be a very strange problem indeed.

1. While booted in Win98, run Memtest86 and check memory thoroughly. XP is tickier about memory than 98. Change out RAM, if needed.

2. Take a spare HDD and reset to factory defaults using manufacturer's diagnostics available on their web site. This should include a "low level" format which is basically writing all 1's or 0's to hard disk. Takes a while.

3. Try installing XP on pristine HDD from above and see what happens. Let us know results.

I don't think copying ntfs.sys to problem installation will help.

One other thing to try is flashing BIOS in case it is corrupt or a critter is residing there.

Good luck.

Dalton

by willcomp

A question.

Are you receiving ntfs.sys error after install of XP or during installation process?

by daz'n'ash

I have tried clearing CMOS, replacing RAM, replacing CPU and even replacing the motherboard. The hard drive will not accept any windows installations at all now. Could it be a faulty drive or something else?

by glyall

after trying all the other answers
check the capactitors next to the CPU
if any are not flat on top they are bad
you will have to replaced the motherboard

good luck

by wlbowers

How old is the box. It could have some hardware that is just not compatable with XP.

Post the name brand of the box or the motherboard and we will check them out.

Lee

by daz'n'ash

It has no specific name brand such as IBM, or HP. It is a custom made PC. It is 3 years old. I have replaced all but the hard drive now and still get problem with ANY attempt to install ANY windows o/s

by daz'n'ash

Thanks to all for your helpful comments. I will try them and let you know if they work.

willcomp, I have tried clearing the cmos in case it was a problem. No difference was made by doing so. The mobo is too old to bother with flashing the bios. I shall try the other suggestions and see what happens.

by blackcurrant

Hi again

You say you have tried all the suggestions listed including a low-level format. Have you tried completely removing all partitions and then recreating a new partition(s) using FDISK?

Next, do a full format, then try to install your OS.

Good luck

by daz'n'ash

I already thought of that, unfortunately it made no difference. Thank you for taking time to answer.

by daz'n'ash

Blackcurrant, yes I have tried LLF and wipe the entire disk. I have tried FDISK and reinstall with no positive result. I just tried 3 different HDDs and the same thing happens. WinXP install to the point where it says.. Setup is starting windows ... and it just hangs there. Win98 just BSoDs and WinME hangs at 76% detecting hardware with 14 (Microsoft Minutes) remaining. What else could it be?

by sgt_shultz

did you say u flashed the bios to latest greatest?
it aint't the hd, it's the controller, betcha

by daz'n'ash

Bingo! Disabling APIC in the BIOS made a difference. However, the motherboard definately has a problematic BIOS. I won't allow complete cleaing of CMOS and will not run stably when the CPU is clocked to run as 1800+. Swapped the mobo again for another and all works well now. Thank you for your help. My apologies for the rejected answers. Nothing personal.

by willcomp

Let's see if I have all this correct. You have:

Flashed BIOS
Swapped RAM
Swapped mobos
Tried several HDDs including one or more reset to factory state

What we should be left with are common components, if any.

Probably down to video, PSU, and CPU as suspects. Have you swapped out any or all of these?

Also, just for safety's sake, was RAM you used known good?

What you're fighting sure sounds like RAM or video adapter at this point.

Dalton

by willcomp

OZiT,

Just because RAM is new and name brand doesn't mean it's not faulty. Have seen bad sticks from several major vendors, especially high speed DDR (DDR400 or greater).

by daz'n'ash

You were partially correct, the AGP card cooling fan had locked up and was definately running hotter than it should. Thanks again for your helpful insights into this problem.

by daz'n'ash

willcomp, the RAM is a 512mb DDR 333 Legend ram. It is new, never before used. PSU is original, however unlikely that a PSU would cause this. Might try another one anyway. I took out the AGP card and using the onboard video as a process of elimination. The CPU is an AMD Athlon 1800+ and known to be in good working condition, never overclocked.

Any other suggestions are most welcome.

This discussion is closed to new replies.