All 4 routers in OSPF area 0 and make sure they can ping from end to end.
In R1:
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#int serial 0/0
R1(config-if)#ip address 10.10.10.1 255.0.0.0
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
R1(config-if)#ex
R1(config)#router ospf ?
<1-65535> Process ID
R1(config)#router ospf 150 (we can assign any process IDs from 1-65535)
R1(config-router)#network 10.10.10.1 0.0.0.255 area 0
R1(config-router)#^Z
R1#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
R1#
R2 needs clocking
In R2:
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#int serial 0/0
R2(config-if)#ip address 10.10.10.2 255.0.0.0
R2(config-if)#clock rate 64000
R2(config-if)#bandwidth 64
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
R2(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
R2(config-if)#ex
R2(config)#int serial 0/1
R2(config-if)#ip address 20.20.20.1 255.0.0.0
R2(config-if)#clock rate 64000
R2(config-if)#bandwidth 64
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/1, changed state to down
R2(config-if)#ex
R2(config)#router ospf 151
R2(config-router)#network 10.10.10.0 0.0.0.255 area 0
R2(config-router)#network 20.20.20.0 0.0.0.255 area 0
R2(config-router)#^Z
R2#
%SYS-5-CONFIG_I: Configured from console by console
R2#wr
Building configuration...
[OK]
R2#
In R3:
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int serial 0/0
Router(config-if)#ip address 20.20.20.2 255.0.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
Router(config-if)#ex
Router(config)#int serial 0/1
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
Router(config-if)#ip address 30.30.30.1 255.0.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/1, changed state to down
Router(config-if)#ex
Router(config)#hostname R3
R3(config)#router ospf 152
R3(config-router)#network 20.20.20.0 0.0.0.255 area 0
00:20:04: %OSPF-5-ADJCHG: Process 152, Nbr 20.20.20.1 on Serial0/0 from LOADING to FULL, Loading Done
R3(config-router)#network 30.30.30.0 0.0.0.255 area 0
R3(config-router)#^Z
R3#
%SYS-5-CONFIG_I: Configured from console by console
R3#wr
Building configuration...
[OK]
R3#
R4 needs clocking
In R4:
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R4
R4(config)#int serial 0/0
R4(config-if)#ip address 30.30.30.2 255.0.0.0
R4(config-if)#clock rate 64000
R4(config-if)#bandwidth 64
R4(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
R4(config-if)#ex
R4(config)#router ospf 15
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
R4(config)#router ospf 152
R4(config-router)#network 30.30.30.2 0.0.0.255 area 0
R4(config-router)#
R4(config-router)#^Z
R4#
%SYS-5-CONFIG_I: Configured from console by console
R4#wr
Building configuration...
[OK]
R4#
Now Ping from R1 to R4
R1#ping 30.30.30.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 30.30.30.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 78/90/94 ms
Now Ping from R4 to R1
R4#ping 10.10.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 93/93/94 ms
R4#
I like to suggest Packet tracer instead of using any other simulator