Discussion Locked

Out of IRQ's

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Running a Gigabyte GA-BX2000+,Pent.III 600,256 M.B. Ram,Plextor 12/10/32A,Creative DVD and S.B Live Value,Internal 100M.B. Zip Drive,VooDoo5 5500, USB Visioneer Scanner,H.P.2000C Printer,and Linsys Networking Card. I am out of IRQ's running Win 98. The Device manager says I would have to disable something else to run the camera I am trying to hook up.Can I gain any IRQ's in any way or share more of them by rearranging them ?The S.B. Sound card is also taking one up for S.B. Emulation 16 (Don't even know what it is). What about adapters to change over the mouse keyboard and printer to USB ?Doe's USB only use 1 IRQ ? Or how about hardware like the Targus USB Mobile Expansion Hub ? Will it free up the IRQ's ? I bought this new M.B. to upgradeto do all this but did not figure on IRQ problems. Been reading alot on them and still don't know what to do. Please help ! Thanx in advance. Tim

15 replies

by tbradley

Disable the serial port or serial port(s) in
system bios, and under win98. This will free up irq 3 and irq 4.

( serial port = com port depending on your system )

Caution, some cards will refuse to accept these irq settings, so some trial and error may be necessary.

S.B. Emulation may be coming from the config.sys file, if loading, and you don't use any dos sound, remove those lines from config.sys, and disable this in system hardware settings.

Caution again, this does not always work, depending on your system board.

by aronya1

I would vote for your idea to use USB. Yes, USB only uses 1 IRQ, but allows you to connect up to 127 devices in a chain. It was designed for situations just like yours. I am not familiar with the Targus hub you mentioned, but I think you are on the right track. There are quite a few USB port adapters that will allow connection of serial or parallel port devices. Personally, I would try not to connect my keyboard this way. Adapters sometimes do not permit full functionality of the device being connected (for this reason, I would try to avoid connecting the mouse to the USB port, also, if it has a wheel or any special buttons, etc.).

Disabling your COM ports doesn't seem like a reasonable choice to me. You will probably need them.
Hope this helps.

Tim

by duck

Here is a different approach.
Go to System Properties. Select the third tab
Hardware Profiles. Copy the original configuration.Rename it something else like
configuration 2 whatever. When you boot you will get a menu to choose which configuration
to boot to. You can setup the hardware differently in this configuration from the original and bounce back and forth.
Just a thought.

by saihib

There is no way you can gain IRQs. Once 1-15 have been used there are no more. The USB controller uses only one IRQ no matter how many devices are being used. In theory two devices can share an IRQ but the devices can't be used at the same time. I'dstay away from doing that because it will probably create more problems than it solves. I would go with the USB hub. In order to free up those scarce IRQs you will probably have to go out and purchase USB peripherals. Take a look at the Xircom website to get an idea of the type of adapters that are available.

by rgravelle

I would disable sb dos emulation for a start.
and remove autoexec.bat and config.sys from
root directory.The machine you are using
should support irq sharing.I would disable
the pnp o/s in the bios and let bios itself
allocate your harware irq's. It wont hurt to
try.If you go into system information, it should tell you what irq's are used by what
and if there are conflicts.

good luck

This discussion is closed to new replies.