5 replies
by nebul0us Accepted solution
by rob miners Accepted solution
Turn off and remove the power plug from the back of the PC and disconnect the monitor cable. Ground yourself by placing the back of your hand on the Power Supply Unit and not moving your feet. By not taking this precaution it is possible that you could inadvertantly cause damage to the PC from an electrostatic discharge.
Carefully remove and clean the golden edge of each memory stick with a soft rubber/eraser, remembering not to touch the golden edge of the memory stick. Check with one stick at a time, remembering to disconnect the power from the PC between switching the memory modules.
While you are in there remove the Video (Graphics) Card and clean the golden edge as well. Reinsert it and reconnect the monitor when you are ready to start the PC.
Keep us informed as to your progress if you require further assistance.
If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D
by ---tk--- Accepted solution
by Former member Accepted solution
1 Short Beep One beep is good! Everything is ok, that is if you see things on the screen. If you don't see anything, check your monitor and video card first. Is everything connected? If they seem fine, your motherboard has some bad chips on it. First reset the SIMM's and reboot. If it does the same thing, one of the memory chips on the motherboard are bad, and you most likely need to get another motherboard since these chips are soldered on.
2 Short Beeps Your computer has memory problems. First check video. If video is working, you'll see an error message. If not, you have a parity error in your first 64K of memory. First check your SIMM's. Reseat them and reboot. If this doesn't do it, the memory chips may be bad. You can try switching the first and second banks memory chips. First banks are the memory banks that your CPU finds its first 64K of base memory in. You'll need to consult your manual to see which bank is first. If all your memory tests good, you probably need to buy another motherboard.
3 Short Beeps Basically the same thing as 2 beeps. Follow that diagnosis above.
4 Short Beeps Basically the same thing as 2 beeps. Follow that diagnosis above. It could also be a bad timer
5 Short Beeps Your motherboard is complaining. Try reseating the memory and rebooting. If that doesn't help, you should consider another motherboard. You could probably get away with just replacing the CPU, but that's not too cost-effective. Its just time to upgrade!
6 Short Beeps The chip on your motherboard that controls your keyboard (A20 gate) isn't working. First try another keyboard. If it doesn't help, reseat the chip that controls the keyboard, if it isn't soldered in. If it still beeps, replace the chip if possible. Replace the motherboard if it is soldered in.
7 Short BeepsYour CPU broke overnight. Its no good. Either replace the CPU, or buy another motherboard.
8 Short BeepsYour video card isn't working. Make sure it is seated well in the bus. If it still beeps, either the whole card is bad or the memory on it is. Best bet is to install another video card.
9 Short Beeps Your BIOS is bad. Reseat or Replace the BIOS.
10 Short Beeps Your problem lies deep inside the CMOS. All chips associated with the CMOS will likely have to be replaced. Your best bet is to get a new motherboard.
11 Short BeepsYour problem is in the Cache Memory chips on the motherboard. Reseat or Replace these chips.
1 Long, 3 Short BeepsYou've probably just added memory to the motherboard since this is a conventional or extended memory failure. Generally this is caused by a memory chip that is not seated properly. Reseat the memory chips.
1 Long, 8 Short Beeps Display / retrace test failed. Reseat the video card.
Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.
by 1bn0 Accepted solution
Check the power supply before you do anything else. Buy a tester or takeit to a shop. The power supply in eMachine usually gets the blame for failures. This is primarily a precaution but I consider it of higher importance than with other brands of computers.
I have personally dealt with one that was booting O.K. but eventually POPPED! halfway through boot up and took the motherboard with it.
I agree with tkrl26 that it does sound like a fan / heat issue. The fans should turn freely with no power applied and usually will spin up to speed at power up.
Don't forget, the power supply usually has a fan as well. An overheating power supply can be as bad as a failinf one.
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending