Question Locked

pc powers up ...then turns off

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have an emachines pc that won't stay powered up. I've noticed that as soon as I plug the power cable in to the surge protector the light on the surge protector turns off as if there is a short. When I push the power button the pc powers up but as soon as I release the button it turns right back off. WHat coulod be wrong??? IT stopped working after a car ride because I was moving. WHen I went to plug it back in is when all this happened.

7 replies

by meridenscrafts

open up your computer, make sure you are well grounded. Check all the cards, memory,etc. to make sure all cards and memory are seeded in there slots. You may have bounced it around in the car and something came loose. especially your memory sticks. Check to see if it might be getting real hot somewhere. Switch box, video card. check to see if there is a lot of dust inside, may have gotten knocked down on something. Hope it helps
dust can get inside real easy.

by hal 9000

If it's longer than 5 seconds or so this is what should be happening as you should only push on the Power Button to give a ripple on the powered on 5 V DC line to start the Power Supply running.

After the On Button has been held in for a certain amount of time the unit will be powered down this can happen when you release the On Button or prior to that depending on the hardware involved.

But if you have moved the unit open the case and look for a build up of dust and other rubbish inside the case and clean it out without using one of those Static Cleaners which will destroy the unit. I tend to use Compressed air to do this with but a vacuum cleaner will do as good a job.

Lately with a lot of rubbish being built up in cases I've been replacing quite a few Power Supplies because they are damaged by all this dust and other rubbish which causes shorts to occur so if the device is no longer working try a different Power Supply but first make sure that everything is properly connected as the trip could have caused some power connectors to work slightly loose and they are no longer making proper contact.

You should also check the RAM and any Plug In Cards which may have been moved slightly as well.

Col

by jreyesz28

I have to hold the button in for it to stay on and it just goes to a screen that tells me that the mouse is not connected and that there is an error.I am going to take the case off and give it a thurough cleaning as you recommended and make sure everything is well connected. THank you for your replies!!!

by sgt_shultz

just to keep from having to open the box, maybe just have a hard look make sure keyboard and mouse are in correct port, no bent pins. or low batteries in wireless etc.
watch screen very carefully at this partial boot. see if you can enter setup and study all the configuration options there that have to do with booting and hardware checking at boot time.

by jreyesz28

so i cleaned it out. Lots of dust. Made sure alll connections good. At partial boot it says cmos check error and the keyboard won't work either. I try to hit F1 to enter the system option on the screen and won'[t do anything. Everything is connected in its place and no bent pins....This thing just wont boot up to windows and still the same thing...I hit the on switch and as soon as I let go it shuts off. kinda giving up on it....what could I do with the parts in this PC is anything salvagable?

by hal 9000

This is a common issue and is easily fixed by replacing the coin Battery that should be a CR2023 or a replacement for that type of Lithium battery.

When you replace the battery you need to remember that the side with all the markings goes away from the M'Board. Now for the main problem do you have a USB Keyboard? If so grab a PS2 and use that to do the initial setup of BIOS after replacing the battery as the USB Drivers are not loaded till much latter in the boot sequence and you will be unable to enter BIOS and change the settings which should at the very least should be the Date & Time and whatever else you need changed things like the Boot Order come to mind and L2 Caching as well but this depends on the make of the M'Board as to what you'll need to change.

Col

This discussion is closed to new replies.