Discussion Locked

PC won?t turn on...at all

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Here is the problem, I have a 300w PS powering a PC...Celeron 2.40GHz, 512MB RAM, DVD, CD ROM, CD-R/RW, 3 Chassis Fans, HDD Fan(mounted onto the HDD,underneath) and a Tt 4 Fan control 5 1/4? deck.
About 3 hours ago, it just turned off and won?t turn back on. I noticed that the Volts on the PS were moved to 230v not 115v which it was supposed to be on. I tried changing the PS to a 350w PowerMax the PC just turned on for 3 seconds. I assume that I need a 400w to 500w PS. Is there any chance that I damaged the motherboard? It is a SOYO PVM...Prescott Ready. Or damage the Processor? Why won?t it turn back on?

16 replies

by darrynmarr1979

this is gonna sound sooooo stupid, but have you checked the fuse in the plug lol? and there is also a fuse in your power supply unit, which has probably blown as its designed to. my advise is change the fuse in your plug, if that doesnt work probably means the power supply unit is dead, replace it and try testing the parts on your computer on a different machine

by cyberghost_1

I tried changing the plugs and power supplies. I just put in a 400w PS and a different plug connsected to a big surge protector I have

by willcomp

Believe it on not, power supply set for incorrect higher voltage should not harm any internal components or the power supply. Feeding 230v to one set at 115v is another matter. Usually a PC won't power up and run with voltage set incorrectly, so shouldn't have been that way long.

Disconnect all your drives and case fans and try to boot using another power supply. Sequence loads back until you find problem. I'm assuming that there is a short somewhere.

Dalton

by willcomp

A word about power supplies. You will be better off with a high quality 350 watt PSU (e.g. Antec or Enermax) than with a cheap 400 watt or 450 watt PSU.

For your loads, a quality 350 watt is adequate. Go with a quality 400 watt or better if you want to be safe. An average 300 watt PSU isn't sufficient

I'm running an Athlon 3200+, 128MB Radeon 9550, dual 120GB SATA HDDs in RAID 1, DVD RW, DVD ROM/CD-RW, removable HDD (mounts in 5.25" drive bay and powered internally), 1GB RAM, and 2 case fans (120mm and 80mm) in a Cooler Master Cavalier case with stock 350 watt PSU. No power problems to date, but that's a good PSU. Have a quality 450 watt on hand, if needed.

by dmiles

Did you get a burning scent from the power supply?
Check that all connections on the board are properly set

Begin troubleshooting by going with a bare bone setup,with only the graphics and memory in system

Check to insure that the cpu fan is operating,then proceed to add with checking the memory is installed in slots.

Check for any overheating of the cpu

The only way that the board could be the culprit is that you have a component on the board is going bad or only works when it is cold

by rrenn46

If anything got damaged it is the board.First the power supply must be atleast 400 or better with everything your running.the way to test is pull everything except video,memory and cpu. turn on if the fan works and your pw light is lite and it doesnot boot most likely its the board.and if you look at it this way its probably the least expensive to replace.try pulling the memory then turn it on.if no beep code then its down to the cpu or the board.but I would replace the board.

by sgt_shultz

on for 3 secs sounds like some kinda clue all right. i would say it means bios ok but first check of something makes it unhappy. that might be processor, do you think? or maybe it can't find 5v's on that power wire. or maybe it wants fans spinning and they are not.
i agree the mb sounds damaged but you didn't damage it. correct me if i am wrong guys but underpowering the ps only puts ps at risk, yes?
if you have pulled off everything and nothing is bad and pulllind down power (leave on known good hd or cd/dvd drive on there as switch ps's need a load to operate correctly and for you to measure voltages correctly) only hope now is to see if something user changeable on the mb blew. unless you find it is a bad periperal which i rarely see. see lots of dead mb's tho. if you don't have ram and processor to swap in you can't tshoot whether it is those or mb.

by cyberghost_1

For some reason, It worked when I connected the Processor fan on the bottom of the MB instead of the top where it regularly goes...any ideas

by sandeep_ty123

Yeah,check for burning smell if any from the motherboard.Also,turm on the system after you open up the chassis to find if all the fans are spinning or not.
Also,when the system is turned off....unplug it from the power supply....press and hold the power button on the system tower for about 15-20 secs(yes when it is powered off),so that it releases the flea power..then try rebooting by plugging it back.

SANDEEP
INDIA

This discussion is closed to new replies.