Discussion Locked

Ports and modems

0 helpful
23 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I would like to know what Windows 95 means by the error: "Unable to open port". This error occurs when I attempt to test the modem on my user's PC. I have com ports 1 thru 4 available in Device Manager. I have de-installed the modem and re-installed it, hoping Windows would assign a port not in conflict. This PC is a Compaq Armada 1700 laptop

23 replies

by don_brill

If the modem is not external (such as PCMCIA), an easy solution is to de-install the modem and remove any com ports you're not using from Win95's device manager; reboot and disable the com ports via the BIOS setup (F10 at boot); then re-install the modemon COM1 (3F8, IRQ 4) or COM2 (2F8, IRQ 3).

by will-b

in addition :
if you have modem software (like in HST modems), you can assign a port and maybe IRQ too by that software. Try to check the manual and look for installation tips and troubleshooting.

by hallkr

Sounds like you have an internal modem so thats how I'll answer your question. If this is a Win modem (software driven) it can be tempermental. But the same procedure can be used for both hardware and software modems. First reboot your computer and enterBios setup. Disable Serial port 2 (com2). Allow to finish booting and your modem should be detected. If this doesn't happen, go to device manager delete your modem and delete com2 if displayed. Reboot modem shoul;d be detected. When Windows asksfor the drivers specify have disk and point to the drive they are located on. When the expected driver (on top display) matches your current driver (bottom display) select O.K. and your up and running.

by rcastellan

This is port conflict. The open port messege means its looking for the modem and it see more than one thing using the same com port address and gets confused and can't find the modem. If you have 4 com ports listed you have too many. Com 1 uses IRQ 4 andcom 2 uses IRQ 3, Com 3 uses IRQ 4 and com 4 uses IRQ 3 and this is why your having an IRQ conflict. Go to device manger and remove com 2, 3 & 4 and the modem. Then reboot the computer. It should put one com port back in and install the modem tothe proper port.

by rindi1

Possibly your port is already in use by an open application, like a fax software. Try disabling all background activities then try again.
Good luck, Markus

by medvisions

Reboot - go to BIOS Disable both COM ports.
Boot - Go to windows95/98 safe mode.
Go to Device Manager. Expand Modem and remove from device manager.
Reboot - Let windows find the modem and (presumably a PNP modem) if not make sure you set it for COM1 IRQ4 or COM2 IRQ3. Load drives. Test modem in Properties.
Does not work. Go to Registry Hkey_Local_Machine\Enum look any root which pertains to the modem., Delete that section only. First, however, make a back of the Registry.DAT file (hiddenfile in Windows folder) Use attrib to bring it down copy and use attrib to bring it up again.
Use Enum section is deleted reboot. Reload the drivers. Does not work. Go to the internet of the modem maker and get new drivers. And go back to the beginning and try again.
Good luck Harry

by jo__kelly

1: Remove ports in Device Manager
2: Reboot
3: Enter BIOS
4: Disable Ports
5: Power down and reseat modem
6: Power up and let windows detect modem
7: Write down the IRQ settings
8: Reboot and enter BIOS
9: Set ports to auto or manually set using other IRQ's than what windows is using for your modem.

by hjs

All the answers above are good, but there is one thing that I have ran into. The modem is bad. I have gotten this error msg when the modem will not hang up. P.S. winmodems are the worst at this.

by asger

Check to see that the port is enabled and has no conflict. use the my computer properties, device manager to view.

Make sure that the modem is pointing to the correct port, check this from the controll panel.

Try removing the ports and restart your machine.

by eduardo

Is your modem PCI? If it does, check the IRQ. Sometimes PCI modems select IRQ's 9 to 11, that setting don't work a lot of times. Check your motherboard BIOS. Is the modem IRQ set to 3 or 4 on the BIOS. Leave it that way. Change IRQ 3 to PCI/ISA PnP.Then change the IRQ where the modem is set to ISA. Save the changes to your BIOS and reboot the system.
Check now the device manager to if the modem is on IRQ 3. If not , try to change it manualy on the device manager. Repeat the process if necesary. Sometimes this takes a little to get it right.

by eevans

I have also seen this problem when a mouse driver "grabs" the port at bootup.

I would temporarily remove any mouse driver and re-test the modem.

Hope this helps

This discussion is closed to new replies.