Discussion Locked

Printer causes reboot of win 2000 SP4

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
When I power on my HP 7031xi printer (connected to USB) it reboots windows 2000 SP 4, no errors. Eight out of ten times it will reboot with no errors? Reinstalled USB & printer drivers, no go. On line with HP support for 2 1/2hours, still no go.

16 replies

by w2ktechman

Win2k automatically reboots when a blue screen occurs. You need to turn this feature off and see what the blue screen is to further troubleshoot.
Or
Is the printer plugged into the same electrical socket as the computer, monitor, etc. Try a different outlet (on a different fuse) and see if the problem continues.

by mikec.mikec

Thanks for the reply. I get no "Blue screen of death". I also have an HP III connected thur LPT 1 which does not cause a reboot. My cousin has an HP printer (differant model)also connected thru USB, when she had win 98 no problem. When she upgraged to win 2000 SP4 now she has the same problem; power on printer reboots computer. Did not happen with win 98. Any other ideas?

by jschein

1st thing is to put the proper printer MODEL # down... This will help us assist you.

2ndly, have you gone to HP.com --> support. HP All in one printers and some printers have an issue with USB. If you do not have the drivers fully installed or the latest USB updates from microsoft, the connection will make the PC reboot.

by mikec.mikec

Ischein, in my question I state that it is a HP 7031ix connected thru USB. 2nd I stated that I was on line with a HP tech for almost 3 hours. As per HP I did reinstall the USB drivers and checked for the latest Printer diivers as well.

by joseph moore

You know, Win98 and Win2K handle USB differently. 98 probably only has USB 1.0, and Win2K does USB 2.0
So, my thoughts on this are for you to get an updated motherboard BIOS flash, with the latest BIOS version. Flash the BIOS with this new version, and see if that fixes things. You can call HP again, and they can help you with the BIOS update, or just go to their site for your computer make/model/speed and look for BIOS updates; get the most latest one.
hope this helps

by mikec.mikec

I only meation win 98 to rule out any printer or power problems. I have checked for the latest MB BIOS and they are the latest. I really believe that it is a HP,USB, win 2000 problem. But I have already done all that is sugguested here so far. I find it hard to believe that I and my cousin are the only ones having a reboot problem with an HP printer connect to USB running win 2000 SP 4. Thanks again for your responses.

by brddog

This may not be an answer but let me try some suggestions.
First, did you try starting computer with printer on? (I leave mine on)
Second, you say it will occasionly reboot with error, do you have the error code? If so you could input that at microsoft to see if there are any clues to a solution.
Third, did you try another printer on this system?
Fourth, I cannot find this model on HP's site. If this is an older USB 1.1 and the motherboard is USB 2.0 this also could be the problem (or printer is USB 2.0 and MB is USB 1.1)
Hope this helps

by mikec.mikec

Oops. Its a 7130xi officejet. If I leave the printer on, no problem. When it reboots there are no error msgs given, no blue screen. I have an older HP laser III connected to LPT 1 which DOES NOT reboot when I power it on. All on same power strip. I understand that some say it might be a power spike, but sometimes I can cycle on-off the printer eight times and not get a reboot?? I reinstalled the USB divers, but have not looked for new ones. Will check that out tonight. Thanks for your response.

by desktopgeek

Everytime I have seen a computer reboot on its own when something is used has always been an IRQ conflict.

by mikec.mikec

The problem is intermittent. If I turn on the printer before the computer, no problem. I have looked at everything and there are no conflicts. Sometimes I can turn it on 6 times in a roll and no reboot. This is the only USB device that I am using, and I have no other USB device drivers loaded. I can turn on the printer while the computer is going thru the POST, and it will sometimes reboot. This has been happening from day one.

by hb_bc

Some system will boot from a USB source. That maybe what the printer is doing to your computer. You could go and look in the BOIS to see and if it is set to boot from a USB and if so disable it to see if that fixes your problem.

If that is not the problem you may want to go HP CustomerCare site here http://h20015.www2.hp.com/hub_search/document.jhtml?lc=en&docName=buu01860&prodId=hpofficeje91469&cc=us and read the section about (Problems with power) it talks about one of the symptoms being restarting the computer when try to active the printer.

by mikec.mikec

I was on line for 3 hours with HP support last week, already tried this. Thought I fixed it when we reinstalled the USB drivers. I was able to restart the printer 6 times then on the 7th try it rebooted the computer :(

by hb_bc

Is that the only item that you have pluged into a USB?
If not have you tried to power on the printer with it being the only thing pluged into a USB port or going though a external self powered USB Hub?
I"m just curious if it's a power problem.

by esymms

I am also experiencing the same issue on a HP d530 small form factor PC. It has the most recent bios, the most recent Intel chipset drivers (January 2005) and The most recent windows updates. We run w2k SP4 standard. My officejet is a d125xi.

The BSOD message pertains to UHCD.SYS which has something to do with USB Drivers. I know this really isn't an answer, but I hope the additional information helps. This is also the only USB device on the PC.

This discussion is closed to new replies.