32 replies
by zbrain75
by averytoledo
by wanderer
You don't have a system loaded on your laptop, if you have a win 95 boot disk, put it in the A: drive and boot the PC. At the dos prompt type: "sys c:" without the quotes, and hit enter. This will transfer the system files to your hard drive and you will be able to boot to the C: drive. But, I assume you are trying to load win95 on your pc, not just get it to boot. There are a couple of options depending on your hardware configuration. The easiest thing to do is have a friend with win98 makeyou a start up disk. A win98 startup disk will give you the option of booting your pc with CD Rom support.
1. Boot to win98 start up disk
2. Select Command prompt with CD Rom support 3. Insert win95 cd
4. change directories to the CD Rom (probably the E:\ drive)
5. Run Setup.exe
An other option is to add dos CD Rom drivers to your win95 boot disk, which is a bit more work.
If your PC will boot from the CD Rom, then buy a win98 cd(unlike the win95 cd, it is bootable) or have a friend burn you a bootable
by averytoledo
by clwicks
by averytoledo
by stewart1001
by averytoledo
by jptech
Ok, they are definatly right about setting your pc to boot from the cd-rom drive if you don't have an external floppy drive you can hook up to the system, some ways to enter a bios are "del" key, "F2" key, "CTRL + Alt + Enter", etc. Once you enter the BIOS there should be an option like "Advanced" or something like that, u may need to search around, you should then see a boot priority option or boot sequence option, make sure it is set to "CD-Rom, Floppy (FDD), Hard Drive (HDD). When your done, you will want to switch it back to Floppy, Hard Drive.
Now, I'm not sure if the win95 cd is bootable, but I know the win98 and win98se ones are, so if win95 isn't you could use one of those ones. After you boot off the cd it will most likely load the windows setup.
And a tip if you ever format again, make sure u don't power off the system, and always format with this switch "Format c: /s"
That will make the c: drive bootable. Also it is a good idea to have cd-rom drivers in your autoexec.bat and config.sys on
by averytoledo
by rattlesnake1
by averytoledo
by brent
by averytoledo
by aplustoz
You stated that you only have a CD ROM attached to your laptop, implying that you do not have a floppy drive. You also stated that you are trying to install Windows95 on your computer.
Unless Windows95 has changed really recently, it is not bootable from a CD, so this pretty much limits your options (in my estimation) to:
1: Adding a floppy drive and booting from a floppy.
2: Taking your Windows95 CD to a friend who has a CD Recorder, and have them copy your Win95 Directory in full onto a blank CD and adding system files to that CD, then boot to the CD (setup your boot options in CMOS as you were instructed by others previously), copy your system files to your hard drive, then go to your Win95 directory on your CD-ROM and type SETUP.
3: Find someone who has a Windows 98 CD-ROM, and boot from that, then switch to your Windows 95 CD, then type setup at your DOS prompt.
by averytoledo
by vinnyd
One Easy way to fix this is to get a 2 1/2 inch drive adpater to plug you lpatop hard drive into a full size computer.
Then you can format the disk again with the /s (system) option to make it bootable. Then you must load the real-mode CD-ROM driver for you laptop hard drive.
After that, you can re-install the hard drive and boot from the harddisk in the laptop. That will give you access to the cd and be able to load win95 again.
by averytoledo
by hjs
by averytoledo
by chau_tuyen
by averytoledo
by ramon
Hi,
Go to a friend's computer running windows 98 on it and create a startup disk. Also make sure that your A:\ drive is the first to boot, place diskette on drive a:\ and answer boot with cd-rom capabilities, this way you'll install the cd-rom drivers, go to your c:\ drive and make a directorie call CABS (md cabs), then copy the WIN98 directorie from your cd-rom into your cabs directorie on your c:\ drive (then type the following x:\(where the x =cd-rom letter)copy win98 c:cabs, when finish copying the cabs files pull cd-disk from cd-rom and change directorie to c:\ cabs then from here type SETUP and you're on your way.
by averytoledo
by doc598
by averytoledo
by medwards
by averytoledo
by bionicdog
by averytoledo
by dmitry
You must have startup disk of windows 95 or 98 when you'll boot from this disk you must type a:\sys c:
then you'll be able to boot from hard drive, but you have formated it, so files you are missed try some floppy for installation of cd-rom drive'sdrivers, after installed cd-rom device drivers, reboot, insert win 9x setup CD type cd d:\win95 or d:\win98 then type setup
PS:
D: - letter of your cd-rom drive
best regards
by averytoledo
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending