Discussion Locked

Remote Office Connectivity

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Scenario as follows: -
A company has two offices miles apart that needs to access each other's resources (mostly data only). However some shares may be confidential between management. Approx 20 (may grow) users users per office. Additionally, being part of the same company they share a common dot com internet email address, but mail has to be diverted to users accordingly.
Internet access for both is a must for all.
Finally users must be able to access mail remotely either via dial up (when they are in town but cannot come to the office) and over the internet (when they travel). Besides email, remote users may also wish to access data files or print files remotely on the office printers for their secretaries.
Any suggestions? Thank you in advance.

7 replies

by net_chip

First of all, make use of VPN (virtual private network) to allow data sharing in both office, as well as remote dial-in access. Establish a private tunnel between both offices to ensure security data flows.

I strongly recommend settting up yourown mail server instead of using a common e-mail address in this case (to divert mails to individual users).

Intranet will be a good solution for remote users to access corporate data files as well as printing on the office printers.

Regards,net_chip

by mckaytech

Getting to the best answer depends on what resources are available to you at each site in terms of servers and data lines.

One scenario might be to have one office as a hub. At that office, you would have a dialup server (RAS), a mail server (Exchange or something similar), and a VPN server. At the numbers you're talking about, a single SBS2000 server might suffice for all these purposes.

Your data line(s) at this hub office could be a DSL with two static IP addresses or two separate lines. One would be for Internet surfing and e-mail and the other would be for a VPN connection to the remote office. Alternately, you could use ISDN to the Internet and frame-relay to the remote office.

At the remote office, you would have the other end of the VPN to the hub office. All traffic from the remote office would travel over this link to the hub office and then onto the Internet or wherever.

What this solution lacks is redundancy. So... as yet another thought, you could have aframe-relay between the two as your primary connection and an ISDN/DSL/multilink connection to the Internet at each office over which you could use a VPN connection if the frame-relay failed. At other times, these lines would provide only Internet access.

paul

by shmaltz

I agree with answer 2. But keep in mind that VPN is very slow even over DSL lines.
The way to design it can be like this:
1. You can set up 2 domains 1 for each location then create the trusts you need so the users at both locations can access thefiles on both locations, the link between the 2 locations is again either thru VPN or leased lines. Set up an Exchange server either at one site and configure it with Outlook Web Access (OWA) for all users of the second location that way you can have them even access it over the internet. Or you can setup Exchange for 2 sites and use OWA just for remote users.
2. You can use terminal services (which is now part of Win2K Server). If you use terminal server then you can have every thing located at just one site (Data servers, Application servers, Domain servers, Email servers, Internet servers,) and the clients can logon to the terminal server even thru Dial up (its faster then using VPN over DSL, since only the screen shots and key/mouse stroke are being sent and received) and that way they can have every thing at both locations. For Remote users over the internet you can use Terminal server (Win2k only, or cytrix metaframe over WinNT 4.0 TSE) in an internet browser. that way they canaccess their Email as they would have been on the lan (they get the whole desktop).
Now for internet access for both locations: if you are going to use a leased line to connect both locations then you only need internet connection at one location. But if you use VPN you need internet connection at both ends.

by royet

Just been 'playing around' with Win2K terminal services. However it would work with having just having a single domain model, but agree with with your suggestions on the the rest. Thank you.

This discussion is closed to new replies.