Discussion Locked

RH9 laptop monitor problem-X won't load

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I?m new to linux so I appreciate patience as well as detail in your responses.

I recently dual-booted my Compaq Presario 2100 with WinXP Pro and RH 9 Pro (I chose to install all packages). Grub is controlling the boot up, no problems there.
When RH attempts to load ?X server? I get the following message? ?I cannot start the X server (your graphical interface). It is likely that it is not set up correctly. Would you like to view the X server output to diagnose the problem?? (When Iinstalled I believe I chose ?Generic Laptop Display 1024 x 768) Linux also recognizes my video card correctly as the ATI Radeon U1.

When I click ?yes? to the above message it reads (after all the info about which version I have of linux, X, etc)?
?(= =) Log file: ?/var/log/Xfree86.0.log?, Time: Fri Jul 25 13:47:40 2003
(= = ) Using config file: ?/etc/X11/XF86Config?
(EE) No devices detected.

Fatal server error:
no screens found?

Then I click ?exit? and get? ?Would you like me to try to run the X configuration program? Note that you will need the root password for this.?

I click ?yes?, log in as root, and it says? ?ddcprobe returned bogus values:? (every probe value just says ?none.? And then it says ?trying with card: ATI Radeon Mobility U1? and the message pops up? ?I will now try to restart the X server again?

I click ?Ok? and after a few failed attempts I end up back at the first error message of linux being unable to start the X server.

If I click ?no? through all the dialogues, I get ?I will disable this X server for now. Restart GDM when it is configured correctly? and I click ?Ok? and get to a bash prompt.

Any help and guidance is strongly appreciated.

Thanks,
Ben Snyder

6 replies

by tech_wiz03

Had similar situation before and trying startx to open the xserver just ran me in the typical rh xconfigurator circle. So at the command line I logged in as root, manually started xconfigurator, did shutdown -h now then cold booted and x server cameup.

by ben

Thanks for the input. The only problem is, I can't run xconfigurator because it was replaced by that redhat-config-xfree86 program. Another friend of mine said that the new config program depends on X to run. How dumb is that?!?

My friend also suggested downloading the xf86config program. Why on earth doesn't RH load that during install? Would you concur that the xf86config would work?

I also tried hooking up an external monitor, but that didn't work either. I got the same errors.

Thanks!
Ben

by tech_wiz03

x86config is part of the original linux as is xconfigurator. These will both get you past your problem. You are right Redhat has taken poetic liberty and changed the way some comon linux suff runs thusly improving performance if X runs but cutting off your abilities if it doesn't.

You can replace their new xconfigurator and x86config with the older origianls using rpm from the command line. Personally, I use Mandrake 9.1 which doesn't take such liberties with core configuration files. Instead they offer choice of using core or their new ones or both.

hope this helps

rick

by ben

Sorry for the delayed repsonse. We were in process of moving from IN to Quebec City and we are now settled into our new home. I am going to try using Xconfigurator, but I'm a bit skeptical. I don't understand why it won't work with the "Generic Laptop Display 1024x768" selected. (I reinstalled RH9 and made certain to select generic disply, but it didn't help anything).

Any more advice would be helpful in the meantime.

Ben

by tech_wiz03

Well Ben;

It could be your laptop display needs to be more than just generic which defaults to 16 color 640x480. The X-server demands 800x600 as a minimum so two things you can try.

1) get the exact specs of the monitor in question from win-xp display properties and chnage the linux display to match as close as possible.

2) re-install linux as an upgrade in expert mode and instead of changing the installe stuff just concentrate on the video adapter and monitor sections and make sure to tell it you want to test the new config. If the new config test fails you will need to play till it works.

best of luck Rick

by tommy46

Hi Ben,
I have XP and Red Hat 8 dual booting on a Presario 2100. The monitor you need to install is "Generic Latop Display Panel 1400x1050.
Horizontal 31.5-90
Vertical 59-75"
If you still have problems change video card driver to Vesa Driver Generic
This should pick up that it's an ATI Mobility.
Hope this works for you.
Cheers,
Tommy

This discussion is closed to new replies.