Discussion Locked

RJ-11 to RJ-45 diagram

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,
I need to convert a RJ-11 jack to an RJ-45 jack. Yes, I know I could jsut buy an adapter but what fun is there in that? :)

Thanks,
Brian Wright
Starving college student
BWright@logicsolution.net

12 replies

by rgrowcock

The wiring is essentially the same for both the RJ-11 and RJ-45 jacks. Especially if you are using Cat3 or Cat5 wire. Each has 4 pair of wires. The RJ-11 uses the blue pair, and the RJ-45 uses the orange and green pairs. The standard for 568A for RJ-45 which is the standards that your Telco should follow are as follows: W/Gr, Gr, W/O, Bl, W/Bl, O, W/Br, Br. You can also wire it to the 568B standard which is: W/O, O, W/Gr, Bl, W/Bl, Gr, W/Br, Br.
The following website gives a pretty good little tutorial about wiring, RJ-45 only though and the connector. http://www.addtron.com/test1/thisted.htm
Hope this advise is helpful.

One other thought is that if you are just using the jack for telephone, is that the RJ-11 will fit into the RJ-45 jack and work just fine. Not sure what your application is though. Roger

by lump_16

Here's what I'm trying to accomplish. I've got a trial version of Win 2000 for school, I'm jsut trying to connect it to our current peer to peer network we already have. We're currently using ARCnet but I couldn't find any drivers that would work with our ARCnet cards in Win 2000. I installed a normal ethernet card and it worked fine.

We have a RJ-11 to BNC adapter so I put together a straight-thru RJ-45 to RJ-11 cable based on the site you refered me to (which I already knew about before hand) but it hasn't worked yet.

Any other suggestions?

Thanks,
Brian Wright
Computer Information Systems student
Terra Community College
Fremont, Ohio

by estebandelatorre

Table 1: How to wire a CAT 5 (EIA 568B) Patch Cable
Connector #1 Connector #2 Pair Nro
1. White/Orange 1. White/Orange 2
2. Orange/White 2. Orange/White 2
3. White/Green 3. White/Green 3
4. Blue/White 4. Blue/White 1
5. White/Blue 5. White/Blue 1
6. Green/White 6. Green/White 3
7. White/Brown 7. White/Brown 4
8. Brown/White 8. Brown/White 4
Note: The first color listed in the color pair is the dominant color of thewire. In other words, White/Orange is a white wire with orange stripes.
You only need wires in pair 1 and 3 (the 4 pines in the center).
However, if you don't wire pair 2 and 4, 10/100 automatic sensing switches could not sense right!!!. Works fine with hubs or cross cables

edt@bancobgn.com

by tocolote

Try to reverse the connector.
1-8
2-7
3-6
4-5
5-4
6-3
7-2
8-1

I thought Arcnet was polarity sensitive. And an ethernet card won't work with it.

by barry hensley

Arcnet and Ethernet are not compatible with each other. Just because you can convert the Ethernet coming from your Win2K server to coax cable doesn't mean it will work on the Arcnet network.

You will need an Ethernet to Arcnet bridge or transceiver (good luck finding one).

Many protocols run on the same type of cabling but are NOT compatible with each other. Token-Ring and Ethernet both run on Cat5 cable but are NOT compatible with each other. Arcnet, Ethernet, Token-Ring, etc. can onlycommunicate with each other through a bridging device that is designed to convert the from one protocol to another.

by barry hensley

By the way, since it is so difficult to find an Arcnet to Ethernet bridge, one way to solve your problem is to install a Network Operating System that supports Arcnet, like NetWare 3.11, on an old machine with both an Arcnet and an Ethernet NIC and use the machine as a router.

by lump_16

Thanks, I figured they wern't compatible but gave it a shot anyways. But what I didn't know about was the bridge or transciever used to convert ArcNet and Ethernet.

I'll look into finding one.

Thanks,
Brian Wright
bwright@logicsolution.net
** Help a starving college student **
Yourname.com from $15/month plus much more e-commerce solutions!

This discussion is closed to new replies.