Discussion Locked

Seagate SATA Dual Booting Errors

0 helpful
2 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

2 Brand New SATA Hard drives Model ST3200822AS .
Problem
I have be facing System Crashes from the Day I bought the SATA hard drives whenever I Dual Boot. WinXP is my Primary OS ,I use Windows 2003 and Linux on Logical Partitions on the First Hard Drive partitions, since I require to use these OS?s.
The SATA hard disk works ok as long as one OS is present, as soon as I install the other OS the primary OS Crashes.
I use SATA 1 = Install all Operating Systems on it. Create different partitions for that .Install Windows XP on C:\ Primary partition, the remaining partitions are Logical partitions E:\ or F:\ for Windows 2003 , and if Windows Dual Works install Linux on G:\
SATA Disk 2 = No OS is installed on it. Only a backup of data and various applications .
Action Taken
I have read Seagate?s website relating compatibility issues of SATA hard drives with various OS?s and have made sure that I comply with them.
I have installed Service pack 1 for Windows XP, as is mentioned on Seagate?s website when using SATA.
I have Used SEATOOLS and did receive error.
Partition 1 (FAT 32 (73.9 GB) DANIEL) Result: Critical Error(s)
3 Critical Structure Error(s)
1 Non-Critical Structure Error(s)
612541 KBytes in 39646 files
2415 directories were found
2069190 KBytes in 22888 deleted files
775 deleted directories were found
ERROR SUMMARY:
Invalid DIR Entry 3
Orphaned Data Blocks 1
I have also run a Antivirus with latest updates to make sure there is no boot virus.
I have also updated my Motherboard Chipset Drivers with the latest ones from Intel.
Have also Run Check Disk of Windows Xp to Check Hard Disk with no errors
My Computer Configuration is as Follows
Processor
Intel 3.20 MHz
Motherboard
Intel D875PBZ
Ram
DDR 400 MHz (512MB + 512MB)
Sound Card
Creative SB Live
Graphics Card
NVIDIA GeForce FX 5200 128MB
Monitor
ViewSonic 19 inch Ultra

2 replies

by cglrcng9

First off, you must install the earlier OS first, then Win XP. Here is how I set mine and many others up. I use a Win 98SE boot disk (Though this should match the OS on D:\). FDISKED and set up my partitions. C:\ for XP (set active), D:\ for Win98SE, Win2K, etc. and logical drives as required in D:\, lettered E:\, F:\, etc. for other OS's and backup/ or storage space.

I Format all the drives starting w/ C:\ (Format C:\, Format D:\, etc.). Then run the Win98Se or Win2K setup on D:\ etc. going up through the drive letters first installing all the upper OS'es except XP.

I copy the Win XP files to a directory I create (C:Windows\Cabs\i386), I can see on C:\ by booting to Win98Se or Win2K on D:\ and using the Windows Explorer I can see C:\ from there easily and deal w/ it in the open. I also add a copy of SMARTDRV.EXE (which can be found on any Win9x system in the Windows root folder), to a folder on C:\ I also create called C:\Windows Utilities.

I then use the Win98Se boot disk (though you will need to use the disk that matches the install on D:\Drive), boot to the disk again and do the following @ the A:> prompt;

C: enter
CD\ (change to root folder of C:\ and append to the folder w/ SMARTDRV.EXE)
CD\C:\Utilities (should be now C:\Utilities)
SMARTDRV (SmartDrive.exe should load here and show a blank line, you can now test to see if SMARTDRV.EXE is actually loaded by typing in SMARTDRV which will show you the status.

I can now choose to install from either the CD fresh or in DOS (which I much prefer) from the copied/pasted files in the C:\ root folder (C:Windows\Cabs\i386), I copied in earlier while I was booted to the install on D:\ (usually Win98SE or Win2K).

If installing from the Cd I ask it to overwrite the existing files (always leave the C:\ file system in FAT32), if from CD then from the A:> prompt;

E: Enter (E:>)
CD\i386 Enter (E:\i386)
WINNT (setup starts and off you go)

by cglrcng9

If installing from the copied files on C:\Drive;

C:\ Enter
CD\C:\Windows\Cabs\i386 Enter
WINNT (setup starts and off you go)

After WinXP sets up it creates the NT BOOT LOADER that allows the NT Boot Loader menu, and from what I have seen lately using the Recovery Panel command DISKPART it creates a very small partition it calls (-:Partition1) that is unnamed and shows up in front of C:\.

My feeling is that you are destroying that bootloader if you install it otherwise as far as order. Load XP last always.

Good Luck, hope that helps.

This discussion is closed to new replies.