Discussion Locked

Sharing DSL

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I want to hook both of my win 98 computers to the same dsl internet connection i use.How should I do this? SHould I put a nic card in each computer, then run the dsl into the uplink on a router?I have tried diffrent ways and can not get it together.

21 replies

by philippe.grimault

Hi,
It doesn't works because just one computer have an Internet adress.

You can also use a proxy to do NAT.
You install 2 network cards in one computer. One for DSL internet connection and the other for private network.
Install a PROXY ( wingate, ... ) on computer which have 2 cards.
And you configure your browser to pass by proxy.

The proxy share one internet connection with your private network.
Take care to your security...

I hope, this can help you.

by calves

You can buy a WinProxy for around 50.00 install it, buy a hub for 30.00 and hook the DSL Modem, and the 2 PCs, and you can share the DSL. I have the same setup in home.

Good Luck!

by rsprince

I used win 98 2nd edition $19.00 bucks from microsoft if your upgrading from windows 98 1st edition. Install internet connection sharing...Part of win 98 2nd edition...

Put nic cards in each pc, plug into hub, and plug your dsl modem into hub, and there you go...

I have there set-up as a peer to peer, works great... There is a file at microsoft web site that will help you do this...

by tysonmathews

I hope you chose the External Cisco 675? you then run from the wall to the router to a hub then connect your COmputers to the hub. And have unlimitted computers. Do not do the proxy thing. Just search ads and news groups. You also didn't state how your ISP connects you to your DSL. But if they sent you a box to connect to the wall then take out the RJ-45 and place it into a hub and then your PC's into the hub.

Thats it.
WALL > ROUTER > HUB > PC's

by tysonmathews

OH, Also after doing so, Be sure you install Netbui on both computers and have the same work groups listed and add Client For Microsoft Networks. This is all located in the COntrol panel under network. If you have a network Nieghborhood Icon then Client For Microsoft networks is installed. And you can right click on it and goto properties then select add protocal and select Microsoft and select NetBui

by jmorris

Here's another possible solution. Linksys, and MANY other companies, make a little 5 port 10/100 switch with an uplink port to your cable/dsl bridge. The device does NAT and firewalling. I've seen it for $179 max and as low as $159. I have a fewfriends who bought it and say it works perfectly.

I hope this helps.

by xaeryth

Make sure you are using Win98SE and install ICS (Add & Remove Programs in Control Panel). Put TWO network cards into this computer. Put ONE network card into the other computer. If you only have TWO computers then connect them with a cross over cable ($10). Connect the second NIC in the ICS computer to your DSL router/modem. Use the created floppy disk to set up your ICS client. If you have any problems use this article.

http://support.microsoft.com/support/kb/articles/Q238/1/35.ASP

I've set up 100's of ICS's without problems but if you have any issues follow the article and everything will be okay.

Corey Hitchcock, MCSE
IT Manager
Interdev Technologies

by jherrin1

there are a plethora of possibilities to do this. The easiest is to hook the dsl to nic A of machine #1 and run a simple program such as winroute then point then set machine #2 to dhcp and reboot. Thewinroute software will provide dhcp for machine #2 and will automatically set itself up on machine #1.

by sean khan

Answer 6 is close but you want a router not a switch. Your DSL modem/router will then connect to your new router which will connect to your hub. Your new router will assign private IP address via DHCP and any future computers will not need to be reconfigured as long as it has DHCP selected.

Modem - Router - Hub - Pc's

by mrval

Linksys makes a DSL router that has additional network ports, this should be all you need and it's relatively inexpensive AND quite slick.

regards

This discussion is closed to new replies.