Discussion Locked

Slow backup performance of ArcserveIT

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have problem about low backup performance of arcserveIT6.6 in netware 5.1.I have checked from novell web side and recommend to set some parameter but after set it also poor performance.PLease see h/w and s/w profile below.
Hardware profile:
Backup server:Compaq proliant 370
Tape:HP DLT 35/70
Remote backup server:Compaq proliant 530
Software profile:
ArcserveIT 6.6 with service pack (build 111.239 01/10/00)
Currently backup performance:
Remote backup :432 KB/S
Local backup : about 1.4 MB/S
Have any idea from you to increase performace?
Thanks,

13 replies

by jimbb

Hi,
Heaps of things to try out. First of all, ideally your tape drive should be on a separate SCSI channel. Second, make sure your server itself is optimally tuned. Check things like packet receive buffers (for remote backups) or cache-parameters (for local backups). Novell has a few TIDs explaining how to tune your server.
And then ARCserve. In \NLM\TAPESVR.CFG, you'll see some standard-values far any given tapestreamer. Your DLT and server can handle far more than these standard parameters allow. Try adding "BUFFERS=20" to the line loading your driver - it will be in the [NLM] or [NLMx] section. This will give you a far larger buffer, allowing ARCserve to fill a larger buffer, which allows your tapedrive to read that buffer more optimally.
You can also add a [CONFIG] section, and add "wshots=xx" and "rshots=xx". xx is a number related to the buffers, read document 10015 on support.cai.com for more details.
Restart ARCserve, and you will see a performance increase already.

Jim

by jawad

We have also expeirenced similar issues with ArcserveIT 6.6 on Netware 5.0 SP5 and 5.1 SP1 on Compaq hardware on a switched 100 MBbit LAN.
The solution we found to work in all cases were network and tape/SCSI systems were eliminated as causes, was the Arcserve push agent configured over TCP/IP.

We now get remote backup speeds of 2.2 MB/S remotely and 2.4 MB/S locally with all the other DLT optimising switches mentioned in the previous answer.

hope this helps

by kevin anderson

That remote speed is WAY too low.

Check to make sure that the server NIC is manually set to the correct speed and duplex. Then verify on the switch, that the port where the server plugs in, is also 'hard' set to 100 full (or whatever).

I'd say that you have AutoNegotiate set on at least one end, and it isn't negotiating correctly. Probablly 100Full connecting to 100Half. The switch will show extreme amounts of errors, but communication will definately still occur.

Kev.

by pntg

Check the Network Interface Card Setting. If it is set to Full Duplex 100 MBPS change it to Half Duplex 100 MBPS.

by chris.riley

Do you have GroupWise installed? I have seen problems when trying to backup the offiles directory (where there are thousands of files). Have a look at TID 10026354 which tells you what changes you'll need to make. Have a look through the activity log and it may give you more information on where the performance decreases (look for the transfer rate - @kb/min).

by estebandelatorre

The same it happens to me. I have a TL891 library (similar harware to 35/70 but inside a changer!)What?ve I found is:
1.- Setting the NIC to half/full or whatever doesn?t make me smile.
2.- Doubling memory al host-> nothing
3.- Push Agent at remote servers, yes, good!
4.- Netware S.P and Arcserve S.P -> Almost nothing.
The ONLY parameter that makes me feel astonsih was the USEABOVE while loading the scsi card and the TApsrv.nlm
Check this section of my ASconfig.ini.
My harware is:
* Embedded scsi card (compaq) connected to 2 4mm dat drives
* Adaptec AHA294X (DIFFERENTIAL SCSI otherwise it will NEVER works fine) connected to the tape library (which contains a DLT 40/80 very similar your's 35/70)
=begin=
[Loader]
CSNLM1=ELON:\ARCSERVE.6\NLM\PFC /NC /PFASCONFIG.INI /M /FELON:\ARCSERVE.6\NLMINFO.LOG
NLM2=SYS:\SYSTEM\TLI
NLM3=BTRIEVE -p=4096 -f=30 -h=60 -l=20 -t=15 -u=0 -s=30 -m=512
CSNLM4=ELON:\ARCSERVE.6\NLM\CSDBAPIB
NLM5=SYS:\SYSTEM\DSAPI
CSNLM100=RESERVED
CSNLM101=RESERVED
CSNLM6=ELON:\ARCSERVE.6\NLM\ASPIBD HOST=0 NAME=BOARD0 NOSCAN USEABOVE16
Adapter0=Board0,Adaptec AHA-294X (ASPI)
CSNLM7=ELON:\ARCSERVE.6\NLM\ASPIBD HOST=1 NAME=SUPEREDT NOSCAN
Adapter1=SuperEDT,COMPAQ Integrated 32-Bit Fast SCSI-2 (ASPI)
CSNLM8=ELON:\ARCSERVE.6\NLM\PFC /NC /PFASCONFIG.INI
CSNLM9=ELON:\ARCSERVE.6\NLM\ASDB
CSNLM10=ELON:\ARCSERVE.6\NLM\ARCSERVE
CSNLM11=ELON:\ARCSERVE.6\NLM\TAPESVR USEABOVE16
...
==end===

There are another parameter that must be changed is in tapesvr.cfg in 4 entries in the config section. Is probabily that when changing the blocksize, you have to REFORMAT the tape, otherwise it will use the current formated blocksize.
Don?t know why Buffer is in twice entries, but it works!!!

[CONFIG]
BUFFER=30
RSHOTS=30
WSHOTS=30
BLOCKSIZE=5
[NLMx]
BUFFER=30
My speed?, oh. 670.000Kb/sec remote
350.000Kb/sec Localy (Humm. no matter for me!!)

This discussion is closed to new replies.