11 replies
by mjd420nova
It seems that you may have an incompatability
with the hard drive formats between your previous
OS and the new WIN2KPro. That's why the floppy
boot routine can't see the hard drive.
by bear531
by cg it
by hal 9000
I think that you'll find FDISK does actually work but if isn't reconsigning the NTFS Partition if you run FDISK can it see a HDD with a Non DOD partition? Option 4 or 5 from memory can delete non DOS partitions I use this all the time when wanting to delete Nix HDD's.
If you can not see a HDD at all with FDISK your HDD has died but it is quite common with NTFS partitions that you get a message that there is no HDD in the computer and you could have a Virus Infection or that some 3rd Party Disk Managers may make the drive unreadable that is the way it should be.
I've never had much joy with Upgrades either they always seem not to work properly when there is a copy of Windows already on the drive. The only time I now use an Upgrade is when that's all that the customer has so I wipe the HDD and reinstall the OS from the Upgrade CD, it reaches a point where it asks for a copy of the Older Windows CD so I just pop in a Win 98 SE CD and then allow the setup to continue with the Upgrade CD.
Whenever you are doing anything big to Windows like applying a Service Pack or an Upgrade you should always BACKUP your critical Data and then proceed with a clean blank HDD.
If you have not done that in this case you may be able to recover your data by removing the HDD from the existing computer and fitting it into another computer as a Slave or even in a USB Caddy and see if you can read it buy that computer that you use for this will have to be able to read NTFS Partitions so that means NT Y2k or an XP unit. I actually prefer a USB Caddy as these are simple to use and don't require any work at all to fit a drive to and see if it's readable.
by hal 9000
If you can recover your data don't forget the E-Mail as with changes to the Anti Terror Laws it is vital to keep every sent E-Mail just in case someone changes the content of one of your e-mail to something nasty and forward it on, without the original you are in for a world of hurt and it is impossible to prove that you didn't send the modified e-mail.
Col
by dmiles
It seems that you have an hardware file that is corrupt,so try the following
This procedure can be used to replace any Windows NT system file. In this example we replace the file \WINNT\system32\drivers\beep.sys.
NOTE: To use the NT V4.0 Emergency Repair Disk utility, you must have the updated version of Setupdd.sys. The updated version is contained in NT v4.0 Service Pack 2 or later.
For more information, please see the following article(s) in the Microsoft Knowledge Base:
ARTICLE-ID: 168015 (http://support.microsoft.com/kb/168015/EN-US/)
TITLE : Files Not Replaced When Running Emergency Repair.
1. The Emergency Repair Disk is created during the initial Setup of Windows NT, or by running the Windows NT RDISK.EXE program. Copy the contents of the original ERD onto another diskette or subdirectory on another machine as a backup. The original ERD information saved should be restored unmodified to the original ERD in case this procedure is unsuccessful or there is ever a need to return to the configuration that was originally saved.
2. Remove the read only attribute on the Setup.log file. This is a hidden, system file on the ERD that can be edited with a text editor. Alter the Setup.log file as in the sample below, replacing the entire [Files.WinNt] section with an entry like the last line in the example. Additional lines can be included if more than one file needs to be copied. The [Files.WinNt] section of Setup.log contains an entry for every Windows NT operating system file. When creating or modifying the entry make sure the target folder for the file is the same as the TargetDirectory value in line one of the [Paths] section. The target folder corresponds to the Windows NT systemroot.
This can easily be done by finding and modifying the original line for the target file in the [Files.WinNT] section.
If this does not work you will need a Windows 98 startup disk to perfor fdisk on the partition for a fresh install
by dlturman
by neil cotton
by neil cotton
by sgt_shultz
did you see this?
Setup from the 16-Bit Winnt.exe File Continues in an Endless Loop
http://support.microsoft.com/default.aspx?scid=kb;en-us;282296
by dlturman
I've been slammed all week on other things. But I intend to concentrate on this problem soon. I really, really appreciate all the good suggestions that have been offered. And I believe this is the BEST tech site I have ever seen.
DT
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending