Discussion Locked

Tire hazard. A must watch. - It could save your life.

0 helpful
52 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Tire hazard. A must watch.

This video is an ABC News Production. It is preceded by a commercial. As soon as the commercial ends, the video will begin.

http://abcnews.go.com/Video/playerIndex?id=4826897

I just watched this video and I think it's worth sharing it with all of you and you can email to your friends and family. This is something I didn't know about and maybe some of you don't either.

Watch the entire video because it's amazing what you're going to learn . It may save your life!

[b][i]40 odd years ago I worked for US Rubber (later to become Uniroyal) and was aware then of this problem with tires. It comes about due to prolonged exposure to UV radiation and isn't as prevalent in tires stored in dry, dark, warehouses. Unfortunately most stores and commercial establishment are illuminated by fluorescent lighting, an excellent source of UV radiation. In fact people who spend long hours under these lights often acquire a bit of a tan. Since seven different people have sent me this recently, it dawned on me that not everyone is/was aware of the potential problem.[/b][/i]

[b]Dawg[/b] ]:)

52 replies

by sleepin'dawg

A lot of store salespeople are part timers, such as students, and are told little or nothing about any of the products they're selling, never mind tires. I don't know about other parts of Europe but in Germany many store clerks have to pass an apprenticeship program on the specific products that they sell; at least it was that way as recently as the early eighties. I haven't checked recently to see if that is still true.

[b]Dawg[/b] ]:)

by captbilly1eye

I was aware of this situation when I was in the car biz.
Always good to be reminded.
However, I tend to believe that the extent to which un-sold tires age is largely dependent on how they are stored.

Are re-treaded tires still being sold? If so, I always wondered the safety of those babies.

There have been numerous recalls over the years based on faulty tread on new tires. I'd like to see a comparison of safety records for tires based on manufacturer and country of origin.

by sleepin'dawg

BTW retreading was never an acceptable way to extend tire life and the practice has been pretty much abandoned now. Recapping on the other hand is differnt. Tires are ground down to the belt or carcass material and a complete new layer is bonded to the carcass. Truck and bus tires are actually manufactured with recapping in mind but it should be noted that a tire can be recapped only so many times. There are laws in most states and provices setting limits on how many time a tire may be recapped; trucks getting one limit and buses usually another, lower, limit.

[b]Dawg[/b] ]:)

by hal 9000

With Recaps the Tread lifts off the Carcus as a Result of Poor Bonding/Carcus Preparation in the process.

But with new tires where there isn't a tread Bonded to the Carcus this shouldn't be happening all that often. It gets very hard to separate one part of a tire from another when it's all one molding that is molded around the Belts of the tire. When you add in Steel & Kevlar Belts these modern Radial Tires should be super strong even with less than perfect manufacturing. The fact that this is happening as much as it does looks more like a sign of Penny Pinching at the Manufacturing Process in conjunction with no staff training of those who supervise the construction of the tires.

But really Who Cares if we as a Tire Maker have a .0001 Failure rate that is only a very small number of the tires that we actually make and we'll replace them free when someone complains. :D

Got to love the Accountants Mentality here.

Col

by ontheropes

you can't have recapped tires on the steer tires but on any other tire it's okay. That's what I 'remember', don't take it as gospel.

by w2ktechman

Mine were made in '06, the same year I bought them.
I guess Americas Tire Center aint as bad as I was told. I know people who get theirs from Sears, Costco, etc..

by jmgarvin

Wow...that's just disturbing. I assumed new meant new.

I had a blow out years ago on my Saturn, and I just chalked it up to bad luck or road debris, but now...it puts that in a whole new light.

by hal 9000

Problems come about as a result of UV Exposure but even then it is more to do with the way that the compound of the tire is adversely affected by less grip but longer life of the tire.

I thought that everyone understood that the Compounds used in tires age and get harder as they get older just the same as a Brand New just from the Makers plant will wear at different rates as it gets older. It will wear quite quickly at first and then after a number of Heat cool cycles it will start to get harder offer less grip but last longer. This is how Tire companies get the Long Liefs of tires.

However having said that having a Modern Tire Delaminate like those shown in that Infomercial isn't a common occurrence. Granted there can be Bad Batches of Tires where the Compound used in their construction isn't right or the Bonding Process to the Belts hasn't been right for any number of reasons and the Tread moves against the Belts generating more heat than it should and shorten the tires life drastically. But to have a Tire Delaminate like that isn't something that should be happening all that often

Part of the problem now days with the Pay and walk mentality is that New Tires are no longer kept in their wrappings and are exposed to a lot of things that previously they where not exposed to but even allowing for poor handling and even worse Stock Rotation what I find difficult to accept is that tires so old are being sold.

Signs of extremely poor Sales Staff Training actually as Tire Technology is an ever advancing thing that is taking leaps & bounds every year in both Construction Methods and Compound Technology. Having a Low Profile tire that old available for sale as New is something that I find very hard to accept. I wonder how this happened.

It's also probably not as much of an issue when you always buy complete sets of tires for your car/s from what was reported here most of those Old Tires where 1 Off sales as apposed to sets of replacement tires.

But having said that I have never seen a tire fail because of age alone there have always been other factors in the life of the failed tire that have been the reason for the failure. If age alone was the only requirement it can not explain how a Racing Tire delaminates on a Top End's Race Teams Car as these tires are not removed from their wrappings till they are to be used and then they are not reused after what they where unpacked & mounted on a Rim to do.

At Bathurst this year several teams had numerous Tires delaminate which was put down to a Bad Batch of Carefully constructed Racing Tires. A good reason if for no other reason to not have a Control Tire as when one fails they all are more than likely to.

I can just imagine it the Indy 500 Called because of Tire Failures at lap 10. :^0

Col

by ontheropes

I've never had a problem but I will be looking for the date code from now on.

My tires are usually blems with some small cosmetic defect that keep them from being sold as new. I've yet to find the blemish on any of them. I've been doing that for over 20 years. I've saved a lot of money that way. So far so good. I know that it'd tick me off to finally buy a 'new' tire and find out that it's actually over six years old.

I drive so little anymore that all I look for is tread depth, measured with a digital caliper. I probably have enough tread depth to last me a couple of years. I also rotate my tires at each oil change. One oil change a year has been my average for the past 3 years. I don't think that most people get their tires rotated. We all do here. I overdo it but so what?

by w2ktechman

Everytime I go for an oil change I am asked to -- usually dont but sometimes do.
Whenever it goes in for regular maintenance, the tires are rotated though.

I think most people have them rotated because they are on the maintenace checklists. Whenever it gets a tune-up, they get rotated.

by ontheropes

I think you're supposed to rotate tires every 6,000 miles so that'd be every other oil change.

I wish my local garage offered oil testing. That's the best way to tell if your oil needs changing. All of the Mobil engineers I used to work with used Mobil 1 and got their oil tested. Mostly they'd just put a new filter on it, top it up and go another 3,000
miles. They convinced me that Mobil 1 is the best oil to use. All of the mechanics where I take my truck use Mobil 1 too. It's expensive but I know of a few rides with 100's of thousands of miles on them and they all use Mobil 1. Just so's ya' know.

by hal 9000

But not on the front where the steering is done.

Still a lot of tires to throw a tread and lots still do if the number I see on the side of the road is any indication.
A friend drives semi's Interstate and on one trip he threw 15 treads. I think that particular trip cost more in Recaps then in Fuel and when he hit the other end he was only 30 minutes late. God only knows how had he had to drive to make up all of the lost time in changing all of those tires.

Col

by ontheropes

I've never heard of anyone throwing more than one on a trip. I never lost one myself, just had a flat. Then the stupid dispatcher told me to just drive on it after I told him I found a large nail in the steer tire. Morons are everywhere.

by hal 9000

I think it was more to do with the recaps that where being used. Some break the rules and then wonder why they have problems. :D

As for a nail in a steer tire well the great truck drivers don't need to steer they just drop the bulldozer blade to .5 of an inch off the road and plow through anything in their way didn't you already know that? :^0

Col

by hal 9000

It can be put down to some form of Localized Damage or poor manufacturing practices when things like that happen. I've seen the results of Brand New tires not being treated correctly and hitting big rocks causing that to happen in the past. But in every case like that is could always be traced back to poor break in of the new tire which had caused the problems.

But in the case of the tires shown in the clip above the entire tread had separated from the Caucus which isn't something that should happen at all on a new tire.

Col

by sleepin'dawg

Make sure your tires are properly inflated. If your tires are radials rotate them front to back [b][i][u]only[/b][/i][/u] unless you are driving on bias plys which can be rotated side to side on a diagonal. Clean your tires, Spring and Fall, with a tire dressing product, like Armor-All Tire Foam, which contains UV blockers. Following a procedure like this should get your tires to their rated milage limits, regardless of age.
Another thing that is handy to have in your trunk, is a small air compressor that can be run off your lighter, as well as a tire guage, either digital or regular. Both items are handy items to have to keep your tires safe and make driving safer for everyone. Make sure your tire pressures are suited to the load you are transporting,(see inside drivers side door post for recommended pressures) ie: if you're a fatass, add a couple of pounds presure. LOL

[b]Dawg[/b] ]:)

by the scummy one

I think my truck can handle 200+ pounds.
Hmmm, but maybe not when I am transporting concrete, dirt, sand, and other....

by hal 9000

If you don't break them in correctly you are begging for failures to occur.

I've seen way too many people fit new tires and then start jumping curves and they wonder why they get bubbles in the Walls. :D

It's never a good idea to mistreat tires but it's even more important when they are new as this sets the trend for their life. Treat them bad from new and they will not last as long as they should. Treat them well and they will last longer that the rated mileage.

Col

by older mycroft

Because if you're out on the road, and you stop to check your tyre pressures you are taking that reading from a tyre that is hot or warm.

The rated psi on the tyre sidewall is for a tyre that is COLD!

Sadly, even when you pull into the forecourt of a garage/petrol station and check the tyre pressures, you are invariably getting FALSE READINGS! ;)

by sleepin'dawg

before you start driving and when the tires will be cold. An alternative would be to wait around for a half-hour or so for your tires to cool down.

[b]Dawg[/b] ]:)

by forum surfer

The reccomended tire pressure is exactly that...reccomended. Check the tread depth for wear. If the center of the tires are wearing faster than the outer edges, particularly at the rear then youare running too much pressure. If the outer edges are wearing faster then there's too little air. Vehicles that see heavy loads often need more than the factory reccomendations and lighter cars the opposite. Then on other tires that are unusually large it's almost impossible to get even wear across the tires. Such as on one of my cars I run 315/35 18's and I rarely get even wear across the tire even though all the suspension components are set correctly. I've run several different sets of expensive tires with the same results. The front end tends to like 31-32lbs and the rear fluctuates between 12 and 18 pounds depending on the compound despite the manufacturers rating of 35 lbs.

by forum surfer

I have a Mustang that is a bit of a hobby for me. I'm currently running close to 560hp at the wheels on pump gas. It's fully carb legal, gets better gas mileage that from the factory (driven conservatively under 3,000 rpms anyway) and can idle in intense heat with the ac on. With the money I have invested in building the motor and keeping it streetable, I would't use anything short of Mobil 1. Synthetic oil does have a drawback in that it breaks down sooner than conventional oil. So if you don't change your oil religously, conventional oil is far safer unless the engine manufacturer requires synthetic. I change my oil every 3K miles mainly because my supercharger shares the same oil supply as the motor and spins at ridiclous rotation speeds. If the motor or the supercharger fail one will destroy the other since they share the same oil, so I use quality oil and you can ever change the oil too often. Any high performance engine builder I've worked with has always reccomended mobil 1. I'm not a vehicle enigineer, but I've built my share of high performance engines over the years and blew a few up on the race track...happens to everyone who plays. I've seen Mobile 1 work wonders on preventing internal wear and tear. Lucas oils also makes quality products/additives that are well worth the price premium.

Rotating your tires is always a good idea since it creates even treadwear. Every 6000 miles would be about right, but it's not an exact science and the best method is to visually inspect the inside and outside tread on the front tires and run your had across them. You will "feel" any drastic uneven wear. At that point it's time for a rotation and an alignment which improves fuel economy, ride quality and wear/tear on the front suspension and steering components.

by sleepin'dawg

to break down when you've gone. at a minimum, double the mileage of regular oil. Better go back and check your facts.

by jamesrl

I use synthetic now when I tow to try and keep the engine temp manageable under load (also have a Heavy Duty transmission cooler). But before I used it in winter as it circulates faster than dino on startup.

James

by ontheropes

I worked with 5 of them on a regular basis and they all said essentially the same thing you're saying. Change the filter at 3,000 miles, top up the oil and go until the next oil change interval. Of course, if you were to do that it'd cut the cost of synthetics in half.

What gets me, I seem to remember that recommended oil change intervals used to be every 5,000 miles back in the 60's and 70's. What happened? Were the oil companies not making enough money? ;\

by forum surfer

But I've seen both types of oil up close and personal and I go through the the old oil each time with a magnet and a clear catch pan ensuring my bearings and internals are wearing normally. I wouldn't go more than 5K miles without changing the oil regardless of the maufacturer's specs. Synthetic provides better durabilty and significantly less wear and tear at start-up (where most wear and tear occurs) and under extreme conditions. But I have never seen it last longer than regular oil in high performance street cars, oval track dirt racing cars, drag cars or my daily driver. The problem I have seen is that when it does break down, it does so very quickly. But unless you're buying the "extended mileage oil" you're not going to get more miles out of it. I'd never trust that manufaturer rating on something I paid for when a routine 3-5K oil change isn't going to hurt anything and it's not exactly expensive. Although the 7 quarts of mobil 1 I have to purchase for my "toy" car isn't exactly cheip either!

by jdclyde

if you see uneven wear, you have a bad part or are out of alignment.

If you fix the car instead of hide the condition, you will get better tire wear, better mileage, better handling and longer life for everything.

As for blowing the engine at the track, I would suspect that it isn't the brand of oil causing this.

by hal 9000

Is that with new engines it doesn't allow them to wear in correctly and seal properly where it is needed like allowing the Piston Rings to do their Job. If you use Synthetic from scratch you'll have a lot of Blow by past the Piston Rings that will never fully bed in and work as they are supposed to.

You need to place High Gas Loads on the rings while the motor is under load to bed in the Rings correctly for a Street Driver so that means going up hills too slowly for the gear you are in and accelerating to place a load on the rings. Within Limits of course,

Of course with a real Race Engine we run them with only the Engine Assembly Paste in them for about 15 minutes to bed things in correctly. Great way to bed in Plain Main & Big End Bearings as well as the Piston Rings but doesn't do anything at all to help bed in Roller Bearings.

Your problem with Boring & Stroking a Stock Engine can not be overcome because the distance between centers of the Bores is just way too close together to allow correct cooling of the Bore to happen. Boring them out decreases this distance even more and causes the heat to build up around the Gudgeon Pin Area of the Pistons and Bores that is between the cylinders.

The only reason why you can get away with decreasing this distance is because American Muscle Motors have a distance of 1.3 times the bore between centers and this can be decreased to less than that by scraping away metal within limits of course. Japanese Engines have a standard ratio of 1.1 times the bore between centers so they are far more subject to overheating around the Gudgeon Pins. This is why you see such dramatic removal of metal from around the Gudgeon Pin Area of Motors to lessen the Heat Build up that would occur if they where fully round.

Also Tight Tolerances between the Pistons & Bores are not a way to improve performance they will improve reliability and cut down Piston Slap but will reduce the available horsepower that the engine generates. To increase the Power of any engine you need to make the clearances between the Pistons & Bore as big as possible while retaining the ability of the rings to seal this part of the engine. I've heard some really nasty Piston Slap on some of the new motors that I have built and they have always been the fastest most powerful motors that have even been used.

Of course they will self destruct very quickly if you use the wrong setting on the Engine Management System I used to make EPROMS for Qualifying that I called Hand Grenades because if you did more than 2 flying Laps that is exactly what they turned the motor into but the Bang was always spectacular. :D

As for Synthetic Oil it's great advantage is it's ability to stick to the Metal Surfaces and it's Film Strength so it's not forced out of where it needs to be on cold starts. This is what prevents the wear but I wouldn't call Mobil 1 a Great Lubricant or even a Good Lubricant just an acceptable one for street use. Personally I prefer the PM option it's just better but it's horribly expensive even compared to Mobil 1 or any of the other Synthetics that are sold to the Mass Market.

It also has another draw back and that is if you strip a motor down that has run it you can throw the parts in degrease bath for 6 months and you'll still have oil in the Galleries when you remove the bits from the Degrease Bath so it makes a mess of you and everything you touch.

I personally run a Mono 50 Grade Lubricant in the Ducati which is an air cooled motor that spins quite happily to 9,000 RPM. When I used to race the 250 GP Racer it would run the same lubricant and was known to spin to faster than 20,000 RPM but that was getting to the Dangerous stage because once you exceeded 23,000 RPM the Piston would make contact with the Exhaust Valve and the results where fairly dramatic. Of course not running any Valve Springs made things safer bit even them with a proper Valve Closing System there are still limits far below the Theoretical Maximum Piston Speed possible. :D

Col

by forum surfer

The only motors I've ever built were old school v8's with carbs other than an old tuned port 350 and my current forray into modular ford motors. (And a handful of 2 stroke racing quads) I actually got close to 600hp out of the mod motor on the dyno with 14 lbs of boost and a much too aggressive tune. We dialed that back and left some room so as not to create lean conditions. And I did break it in as you described after asembly with conventional oil, changing it at 500, 1000 and 1800 miles before switching to synthetic. Honestly building motors for drag racing was so much more trouble free. Keeping things emissions friendly and able to run on 93 is a big headache. I could have built a race motor twice as strong for way less than half of what I spent.

by sleepin'dawg

come filled with a [i][b]"special break-in oil"[/i][/b] which, for warranty purposes, is only supposed to be changed after the manufacturers predetermined mileage figure. After that, the manufacturers suggest certain lubricants but for all they care you could pee into your crankcase. Prior to going with synthetic my lubricant of choice was usually Castrol but in an emergency would settle for Penzoil. I seldom had any emergencies.

[b]Dawg[/b] ]:)

by jamesrl

3000 miles of my driving does not necessarily equal 3000 miles of your driving (or my dads).

Many of the manuals I've read suggest 3000 for severe service or 5000 for normal driving. Severe service being lots of stop and go, towing or other activities thats stress the engine and cause more wear. Virtually all cabs, police cars, delivery vans etc are on a severe service schedule.

I do it too generally since 90% of my driving is commuting to work and a fair part of that is stop and go.

One of the attributes of synthetic is that it is supposed to handle higher temperatures better than dino. You are more likely to hit those in severe service as well.

So if you don't drive much, save your money.

James

by forum surfer

Is engines are built to much more exacting tolerances. Things like the bearing tolerances, the piston and crank case tolerances and the overall engine assembly is built to very tight tolerances. That requires a lighter weight oil. Lighter weight oil, even the good stuff like Mobil 1 isn't going to last as long. Everything back in the 70's, 80's and 90's used mostly 10w30 or heavier. It's rare these days to see anything rated for that. But then again cars today are far more powerful than even the muscle car years. You've got Cobra's, Corvettes, Vipers, BMW's, Mercedes and little high strung AWD turbo cars turning in 11 second timeslips off the show room floor. Something you couldn't do back then without ordering a copo chevy or a one of ford/dodge's many showroom racers like the thunderbolt.

Take the new z06 vette for example. I took a look at the gm tech bulletins on that motor. You're pushing somewhere around 427 cubic inches out of the same basic engine block that in other configurations has way less cubic inches, like 250 and below. It puts out 500+ hp on pump gas. Not that long ago drag racers used the same concept. Take the stock block alter the bore/stroke and you have a 427 "stroker" motor built from a junk yard 350. Even with a competent machinist, these motors are on the ragged edge and often called "hand grenades" because they fail violently on the track and send parts through the block. But the new motors rolling off the lines where everything is built to better tolerances allow everything to be much less finicky. There is still a fine line though, there has to be some room for the motor to "break in". Race car builders buid everything as tight as they can get it because longevity isn't the main concern, those tighter tolerances equal a more efficient motor.

by sleepin'dawg

running on Castrol Syntech. I have my oil analysed every 3 months or 3000 miles or 5000 km and I change the filters. Regardless of mileage, I change the oil in my vehicles twice a year, even if the vehicle in question has only been driven a few hundred miles. In the past, if a vehicle hadn't been driven in over 3 months, I would change the oil but with synthetics this is no longer necessary.

You might ask why it was necessary with regular oil. Very simple. Regular oil has some sulphur content. In my part of the world there can be wild temperature fluctuations, especially during the Spring and Fall seasons. These temperature fluctuations can cause condensation to build up in idle motors and this can combine with sulphur to form a weak solution of sulphuric acid, which could cause scoring of bearings.

I run my diesel vehicles (3) on regular oil for other reasons which I won't go into here. Other than my pickup all the two others have more than 350,000 miles on the odometer and neither has ever had the motor opened up for any kind of repair; they've only required tires, shocks,brakes and batteries from time to time, as would any car, gas or diesel.

[b]Dawg[/b] ]:)

by forum surfer

You still have to keep the appropriate pressure related to the load on the wheel. The usual rating of 35 could be too high or too low.

by hal 9000

As it came from Dr Porsche himself while he was in his semi retirement days I tend it give it a lot of weight.

His direct comments where [i]"Force Feeding any motor is a unnecessary complex operation unless you are looking at delivering a minimum 60 PSI of Boost."[/i] Kind of makes the 8 PSI of commercial manufactures look puny doesn't it?

OH I have designed a motor to work properly with in excess of a 60 PSI Boost and it worked wonderfully though it did take a lot of messing around with exhaust lengths to get the Lag from the Turbo to an acceptable level. :D

Col

by hal 9000

Their advertising centers around [b]A Fraction of the Friction[/b]

Think of Bell Ray in the US and you'll be getting fairly close. :D

Col

by hal 9000

Is that I have pulled motors apart to discover corrosion inside them that has been directly attributable to the Castrol Oils.

The older stuff was great but this new stuff is rubbish. No where near the quality of their older Lubricants this stuff particularly the GTX will pickup moisture and circulate it through the entire motor. You just shouldn't see corrosion on the Main & Big End Journals under any conditions. But with GTX you do.

However on the other side of the coin the absolute best Racing Lube with motors that run on Methanol is still Castrol R but that is a vegetable based oil not a mineral oil. Smells nice as it burns away too. :^0

Col

by forum surfer

Never realy experimented with turbos. I've never went past 14psi, either. Currently running a centrifugal supercharger, which as a nice by product lets me get decent gas mileage below 3000 rpms (albeit slightly low on power). At 3500 things change and it becomes a dinosaur burning beast. Now that I'm older I'm losing interest. With my current motor combo, once I had everything tuned right and dynoed...well, I just kinda gave up. I was very curious to see my track times, but I just don't care anymore. That's not to say that I don't enjoy dropping the hammer at 60 to pass someone on the street and feeling the rear end break loose and smoke the tires a bit. :)

I find it strange Mr Porsche made that comment yet there were many turbo 911's made all running at around 1 bar of pressure. I'm not saying he didn't, just saying that seems odd. I still remember all the up roar created when they put a radiator in th 911. Had an uncle with one of the 84 911 "whale tails" that got me into cars. One of my all time favs, especially likes his in red.

by hal 9000

The Old Man was long dead and buried by the time that the Turbo 911 Came out and with the Red Ones they just went faster.

I do however see a slight problem with calling a Intercooler a Radiator. :D

Yep they do similar type of thing but they are as different in function and construction as it is possible to make. However having said that the then Group C car that the Whale Tails where modeled after did have substantially more boost and where completely different. The Road going 911 Whale Tail was really slow in compression even if they did look the same nominally.

I still remember describing a Turbo to a Machinery Inspector as a Air Conditioner for a motor telling him it was used to pump lots of lovely cold air into the Motor to help keep it cooler than it would otherwise be. That allowed the vehicle to remain Road Registered till they accepted the use of Turbos in general production use. But having a Turboed Lotus Corrina Motor fitted in a Norton Frame was more than slightly different at the time at least. Though it was certainly fun to ride around. :D

OH and 60 PSI is only 4 BAR or there abouts so if you look at things that way it doesn't sound anywhere near as much boost. ;)

Col

by boxfiddler Hot topic

I'm in the mood to nitpick, ain't no saving my life. No option but to croak. ]:)

by sleepin'dawg

I'm in the midst of an overhaul at the moment and am not seeing anything like the problem you're having with GTX. I was using GTX until I switched over to synthetics and am now using Syntex. I'm still using GTX on my diesel vehicles, the old Mercedes TD300 has over 390,000 km on it, and so far no problems. Same for my Ford pick-up with 482,000 miles on it, no problems. My new pick-up is just getting broken in and only has 28,000 miles on it. I've just switched it over to synthetics and after 3000 miles, no problem so far.

by forum surfer

I was referring to when they switched away from air cooling. That was all over the auto mags. Lots of people said Porshe was "selling out" and going to go broke because the die hard core customer base would never stand for liquid cooled Porches as opposed to the old school air cooled ones. You know...the same thing they all cried about when news of the Cayenne hit the streets. I'm a sports car nut and I hope Porches always look like Porches without haveing to read the emblem...but a RUF Cayenne capable of 180+ is just plain cool, SUV or not!

by hal 9000

This is be cause of the Limitations brought about by the Laws that basically tell you what can and can not be done to make a car.

Having said that though the one model car that I worked on at Porsche the 959 was a Liquid Cooled Front Engine AWD that was a real monster.

Nice little play toy though and Ultra Reliable so if people like Jacky Iccks if that is the correct spelling could tear off one corner crack the Oil Pan and still drive it into Camp to be pulled out of the Dakar I think that speaks volumes for how well it was originally designed and put together. But I may be Biased. :D

After the 959 I worked on some Gas Turbine Technology which would have been interesting if they had ever of gone ahead with that technology. They would have created a New Look Porsche that would have been as nice as the 911 or 356.

However I can't say that I overly like the way that Porsche has gone now those SUV's look just wrong and while I do like some of the things under the skin of the Boxters I personally wouldn't actually want to own one but maybe graft the Rear Suspension onto a real 911 Carrera would prove interesting. :D

Col

by forum surfer

Those were on the wall of countless kid's rooms, right next to Meg Ryan! I still love seeing old footage of them racing. The location of the turbos made for some spectacular looking fires, too.

I must say I absolutely abhorred the Cayenne until I drove a friend's Cayenne S Turbo. All the sights, sounds, visceral feelings are there. It's all Porche, though it doesn't look it from the outside to alot of people, myself included.

This discussion is closed to new replies.