20 replies
by syscokid
If you have a portable tape drive available, or a zip drive, that may be one answer.
Also, it's easy enough to install each of the old drives as a slave in the new machine, and copy directly from disk to disk.
by sleyba
by crisisbleeds
One way to get the "data" from the old drives to the new pc would be to connect the drives to the same machine. You could accomplish this by adding both drives to the secondary controller. As long as one drive's jumper settings are set to slave thenwhen it boots it should see the disks and you should be able to pull the data to a partition on your bigger drive (assuming your new drive is the master on the primary controller. Once the "data" is transferred then you remove the drives and put whatever was on the secondary controller back on.
My concern is that you are not only talking about "data" but programs as well. If that is the case, if they are windows based applications you will not be able to transfer the programs, only data (e.g.-*.doc,*.xls, *.mdb, *.jpg, etc.). You will still have to reinstall the programs.
If the user is on a current existing network you could get the old machine on the network and move the files to another machine with larger capacity. You then get the new on the network and copy those files to the new machine. If they are both connected at the same time and have file and printing sharing enabled, you could move the files directly.
Once again, it is important to know whether or not the client needsjust files moved and/or apps moved or reinstalled.
by sleyba
by crisisbleeds
One way to get the "data" from the old drives to the new pc would be to connect the drives to the same machine. You could accomplish this by adding both drives to the secondary controller. As long as one drive's jumper settings are set to slave thenwhen it boots it should see the disks and you should be able to pull the data to a partition on your bigger drive (assuming your new drive is the master on the primary controller. Once the "data" is transferred then you remove the drives and put whatever was on the secondary controller back on.
My concern is that you are not only talking about "data" but programs as well. If that is the case, if they are windows based applications you will not be able to transfer the programs, only data (e.g.-*.doc,*.xls, *.mdb, *.jpg, etc.). You will still have to reinstall the programs.
If the user is on a current existing network you could get the old machine on the network and move the files to another machine with larger capacity. You then get the new on the network and copy those files to the new machine. If they are both connected at the same time and have file and printing sharing enabled, you could move the files directly.
Once again, it is important to know whether or not the client needsjust files moved and/or apps moved or reinstalled.
by sleyba
by sleyba
by mphoffar
Hooking up the HD and just copying files over, I don't beleive would completely do the job. Some may wprk, but I'd be certain theres an ini entry or a reg entry that's critical for the operation of that application. I do not know of a way to transfer a program and have it search for entries it depends on other then reloading the software.
If you don't beleive that'll be a problem, then I feel the easiest way is to just network the two together using NetBEUI for your protocol and enable file and print sharing and just copy them over.
Good luck to you
Mark
by sleyba
by stngfan1
There is no easy way to do this because you are switching the OS. I would use MS/backup and backup the whole system on his old pc. Restore ONLY the program directories to his new pc, and run the install.exe for each program and install it using the same directoires. You won't lose any data, but you have to install to get the programs to run.
Also watch out for programs installed on the D drive, when you restore them there going to think there on D drive still. Running the install.exe and picking the proper directory should cure this.
If you were going to keep the same OS, you can do it without installing all programs.
Good Luck TM.
by sleyba
by corewarrior
moving the win95 HD to the win 98 machine and configuring the Win95 HD a slave on the Primary channel is The easiest way That I know of to transfer data files and folders.
Also an easy way is to network the machines together and tranfer the files/folders over the network.use the copy and paste method as this will retain LFN better.
As far as tranfering the applications to the new system is concerned,that will not work except for application that do need to write anything to the registry.Eudora Pro e-mail is one application that can be moved to a new system,and after coping 2-3 dlls' to the Windows folder,it works fine.Powerquest's PartitionMagic 5.0 or newer has a feature that will move application.I have PM5.0 and although I use it,I have yet to use that feature,so I cann't comment on it's reliability.
An alternative,which is probably not an easy one,would be to tranfer the win95 system to the new Hard drive using Ghost 5.0e or newer and then upgrading to win98.This will allow everything to be transferd in working condition.Although,The upgrade may present some problems,depending on the hardware and how well it is detected by the Plug and play phase of the setup.Ghost5.0e supports LFNs durnig a tranfer.whereas Xcopy will corrupt the long file names of file and folders.
by corewarrior
Update,Partition magic 5.0 will not help you with your machines.
Go to this web site www.alohabob.com and check out this software PC relocator.
This application will transfer applications between 2 machines,The OSs must be similar and a network cable or a parallel cable is used to connect the machines.All setting are transfered,icluding start menu,shortcuts...
Consumer report has a short review on this app.Summary,Works fine with a few minor issues.Price is $49.99
by sleyba
by sleyba
by abatista
There is no easy one step to do this. The best way I have done this is in 3 parts. if your not able to upgrade your Windows 95 to Windows 98 it gets even harder. Part 1 Upgrade your operating system to Win 98 SE. Part 2 1)Install the new hard drive as a slave to the first HDD. 2) Boot up the system and configure the new drive, that is the secondary drive so that the system recognizes it. 3) Fdisk the SECONDARY drive. use Fat 32. 4)Restart the PC back into Win98. 5) Format 2nd Drive without the /S switch. (This is important) 6)Make a bootable floppy disk with your system with the old master still primary. format /s then copy fdisk.exe to the floppy. 7) Click start, Run, and type the following. Then Choose OK to run it: xcopy32 c:\*.* d:\(secondary drive letter) /h /e /c /k
9) after this is done can take up to 1 hour., you can then shut down the PC. 10) Remove first drive (Master) and make 2nd drive the Master. 11) Restart PC with boot floppy. 12) Run Fdisk and set partition to active.13) Your done. You should now have upgraded your drive with all the data and options running.
by sleyba
by bww5195
I aggree with jgg@pilot.msu.edu (Answer 6, I think) about the use of Ghost.
I have used GHOST on about 25 different occasions at work and am VERY pleased with it's performance.
What I do is copy GHOST.EXE to the drive that you want to copy from and shut the pc down. Make sure that the jumper(s) on the new drive is set to 'slave'. Then I use a 'daisy-chain' data cable to add the new hard drive. The source drive needs to be on the opposite end of the cable from the controller on the motherboard with the new drive on the middle connector in the daisy chain data cable.
Boot the machine and let bios accept the presence of the new hard drive.
Run Ghost.exe, it does run in dos mode. Select drive to drive (wording may not be exact...) Select the drive that you want to copy from as the source drive, and the new drive as the target. (Typically drive 1 will be the source if you hooked up the drives in the correct order on the daisy cable, whereas the new drive will be drive 2.)
An easy way to make sure of the source and destination selections is the summary screen that is displayed just before Ghost starts 'ghosting'. Check the drive size of the source to confirm that it's the old hard drive.
Good luck.
by sleyba
by sleyba
This discussion is closed to new replies.
Trending Windows Forum posts
Sort by Trending