14 replies
by pierrejamme
Normal behavior for Checkdisk with both options checked, program says: "the disk check could not be performed because the disk check utility needs exclusive access to some windows files on the disk. The files can be accessed only by restarting windows. do you want to schedule this disk check to occur the next time you restart your computer?"
So you say yes and the reboot. The disk check operation runs before windows loads.
Now if yours says something else then you had better purchase a new hard drive soon.
by badair
Poster rated this answer.
by hal 9000
If you only have one HDD in the machine the above is correct that is what should be happening as Scadisk will only run when Windows isn't.
When it does run it automatically fixes errors that have been made to the HDD if it isn't then try running a Disk Checking Utility from the Drive maker to check the HDD is still all right and not on its way out.
At one place where I did some work they had a computer on a desk that wobbled and it was causing the heads to contact the platters when they ran a BJ printer. They wouldn't listen until the drive died and then they bought a new desk and HDD. No problem since.
Col
by badair
Poster rated this answer.
by avid
by badair
Poster rated this answer.
by dmiles
Windows XP doesn't have ScanDisk !! However, it does have CHKDSK, which is similar. Unfortunately, the interface of Chkdsk is very limited - you only see a progress bar and not what is going on until the end, where you receive a limited report with the Command Prompt Chkdsk - and no report with the Windows-based Chkdsk.
NOTE: as far as Chkdsk is concerned - the boot partition will always be locked and chkdsk can only make repairs upon reboot !!
you can run Chkdsk to simply "check" the partition
you cannot run Chkdsk "directly" with "fix errors" enabled. However, if you try to run it with "fix errors" on the boot partition, the system will give you the option to run Chkdsk upon the next reboot and then it will run and fix any errors. You can run Chkdsk with "fix errors" enabled for any non-bootable partition and it will run without having to reboot !!
Chkdsk from the Command Prompt
Start/Run . . . cmd
chkdsk x: /f - where "x" is the drive letter, and "/f" (fix errors) is optional
Chkdsk within Windows
NOTE: Scandisk is not the same as Chkdsk, although functionally they do the same thing !!! Chkdsk will only run during bootup, and will only run if the system detects a cold boot or power off.
1) double-click My Computer
2) right-click on the drive you want to run scandisk on
3) click the Tools tab and click "Check Now" next to "Error Checking"
4) to fix errors, check the "Automatically fix file system errors" box - and
to run a surface scan, check the "Scan for and attempt recovery of bad sectors" box
5) If the drive is the boot drive, reboot and Chkdsk will run during the boot process before Windows starts. If the drive is not the boot drive, Chkdsk will run without rebooting.
by badair
Poster rated this answer.
by badair
by petremure
by badair
Poster rated this answer.
by jtilley
Hi there!
I have the same happening with XP Home, and have had, since I bought the machine two years ago. BUT, the checkdisk, having noted "a process has access to drive, and therefore cannot repair," also asks me if I still desire the checkdisk. I note click yes, and then simply RESTART. When XP notes that I want a checkdisk done, it will not load anything to disk, but checkdisk will start and do its work, without anything in memory. That's the way it's been, for two years, so see if this is the case yourself. Checkdisk simply wants entire HD to itself, to correct. Hope this helps!
by badair
Poster rated this answer.
by badair
This discussion is closed to new replies.
Trending Windows Forum posts
Sort by Trending